Polk Audio SurroundBar 2000 SurroundBar 2000 Instant Home Theater Owner's Manu - Page 5
Press and release Volume Up - polk iht
View all Polk Audio SurroundBar 2000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 5 highlights
How To Connect Your Bar FACTORY USE ONLY 1 SOURCE 2 20V 2.7A 54W Note: Remove the protective cap prior to inserting cable. TV ANALOG AUDIO OUTPUT R L DIGITAL OPTICAL AUDIO OUTPUT Note: If your TV does not have an optical output, you can use the optical output from your DVD player or your cable/satellite box to connect to the optical input on the bar. Then simply use the other bar input for your other audio source. Check That Your TV Is In The Correct Audio Format The SurroundBar 2000 does not decode the Dolby Digital audio format. Check that the audio format of the input source (TV, DVD or Blu-ray) is set to PCM 2-channel audio. How To Optimize The Sound When TV Speakers Are On You should hear sound from the bar. If you don't, turn up the volume on the bar using its volume control buttons. If your bar is connected to your TV, there's a very good chance your TV speakers are also playing. It's impossible to give specific instructions on how to turn off the speakers for every TV, but here's a way to do it that covers many of the TVs out there. 1. On your TV remote control, find a "menu" or "setup" button. 2. Press this button. You should see an on-screen menu. 3. Next, look for an option to control audio functions and select it. The setting to turn off your TV's internal speakers should be here. If you can't turn off your TV internal speakers, don't worry. Your SurroundBar 2000 IHT will make your TV sound much better. To enjoy the best performance from your bar, you'll want it to play louder than your TV. Use the following steps to adjust the volume balance between your TV and the bar: 1. If necessary, program your bar to respond to the volume up and down control commands of your TV remote. (See "How To Setup A Remote Control For Your SurroundBar 2000 IHT" on pages 8-9.) 2. Turn your TV volume all the way down using the control buttons on your TV. 3. Then, using the volume keys on your bar, set the volume to a normal listening level (do not use the remote control). After you make these adjustments, your SurroundBar 2000 IHT should always be louder than your TV speakers. Then use the TV remote control to adjust the volume as you normally do. 8 Polk Customer Service 800-377-7655 (Outside USA & Canada: 410-358-3600) How To Set Up A Remote Control For Your SurroundBar IHT SmartBar™ Programming Note: For your SurroundBar to respond to your remote control, you MUST FIRST program the bar to respond to your television's original IR (Infra-Red) remote. An RF (Radio Frequency) remote will not work. Other remotes (cable, satellite) will work only after you have programmed the bar to respond to the TV's IR remote. Programming Instructions: Your SurroundBar IHT is currently programmed to respond to the remote control that is included with the product. However, we strongly recommend programming the SurroundBar to also respond to your existing remote control using the steps illustrated below. This will enable you to operate all of your components using a single remote control. While programming the SurroundBar, ignore anything that may be displayed on the TV screen. Example: To teach your bar the "Volume Up" command of your remote control: 1 The SurroundBar is turned on and the LED is solid green. And you have sound coming from the bar. 2 Press and hold "LEARN" for 2 seconds, or until LED blinks orange, then release the "LEARN" button. LED Blinks orange 3 Press and release Volume Up " " LED turns solid orange. LED Solid orange 4 Hold TV remote 1' - 2' from SurroundBar. 1' - 2' Customer Service Hours of Operation: Monday-Friday, 9am-5:30pm est [email protected] 9