Poulan PBA195H42LT User Manual - Page 23

To Remove Hood And Grill Assembly

Get Poulan PBA195H42LT PDF manuals and user guides View all Poulan PBA195H42LT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

SERVICE AND ADJUSTMENTS REPLACING BATTERY (See Figs. 26 and 27) WARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparking from accidental grounding. • Lift seat pan to raised position. • Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor. • Install new battery with terminals in same position as old battery. • First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely. Slide terminal cover over terminal. • Connect BLACK grounding cable to negative (-) terminal with remaining hex bolt and keps nut. Tighten securely. TO REPLACE FUSE Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash. TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 28) • Raise hood. • Unsnap headlight wire connector. • Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor. • To replace, reverse above procedure. HOOD HEADLIGHT WIRE CONNECTOR 03075 SEAT PAN FIG. 28 ENGINE TERMINAL COVER FIG. 26 KEPS NUT HEX BOLT TO ADJUST THROTTLE CONTROL CABLE The throttle control has been preset at the factory and adjustment should not be necessary. If adjustment is necessary, see engine manual. TO ADJUST CHOKE CONTROL The choke control has been preset at the factory and adjustment should not be necessary. If adjustment is necessary, see engne manual. POSITIVE (RED) CABLE NEGATIVE (BLACK) CABLE FIG. 27 TO REPLACE HEADLIGHT BULB • Raise hood. • Pull bulb holder out of the hole in the backside of the grill. • Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill. • Close hood. TO ADJUST CARBURETOR Your carburetor is not adjustable. If your engine does not operate properly due to suspected carburetor problems, take your tractor to an authorized service center for repair and/or adjustment. INTERLOCKS AND RELAYS Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting. • Check wiring. See electrical wiring diagram in the Repair Parts section. 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
23
SERVICE AND ADJUSTMENTS
FIG. 27
TO REMOVE HOOD AND GRILL ASSEMBLY
(See Fig. 28)
•
Raise hood.
•
Unsnap headlight wire connector.
•
Stand in front of tractor.
Grasp hood at sides, tilt toward
engine and lift off of tractor.
•
To replace, reverse above procedure.
TO REPLACE HEADLIGHT BULB
•
Raise hood.
•
Pull bulb holder out of the hole in the backside of the
grill.
•
Replace bulb in holder and push bulb holder securely
back into the hole in the backside of the grill.
•
Close hood.
INTERLOCKS AND RELAYS
Loose or damaged wiring may cause your tractor to run
poorly, stop running, or prevent it from starting.
•
Check wiring.
See electrical wiring diagram in the
Repair Parts section.
KEPS
NUT
HEX
BOLT
POSITIVE (RED)
CABLE
NEGATIVE
(BLACK) CABLE
TERMINAL
COVER
FIG. 26
SEAT PAN
REPLACING BATTERY (See Figs. 26 and 27)
WARNING:
Do not short battery
terminals by allowing a wrench or any
other object to contact both terminals
at the same time. Before connect-
ing battery, remove metal bracelets,
wristwatch bands, rings, etc.
Positive terminal must be connected
first to prevent sparking from acci-
dental grounding.
•
Lift seat pan to raised position.
•
Disconnect BLACK battery cable first then RED battery
cable and carefully remove battery from tractor.
•
Install new battery with terminals in same position as
old battery.
•
First connect RED battery cable to positive (+) terminal
with hex bolt and keps nut as shown. Tighten securely.
Slide terminal cover over terminal.
•
Connect BLACK grounding cable to negative (-) ter-
minal with remaining hex bolt and keps nut. Tighten
securely.
HEADLIGHT
WIRE
CONNECTOR
HOOD
ENGINE
TO ADJUST THROTTLE CONTROL CABLE
The throttle control has been preset at the factory and
adjustment should not be necessary. If adjustment is nec-
essary, see engine manual.
TO ADJUST CHOKE CONTROL
The choke control has been preset at the factory and ad-
justment should not be necessary. If adjustment is neces-
sary, see engne manual.
TO ADJUST CARBURETOR
Your carburetor is not adjustable. If your engine does not
operate properly due to suspected carburetor problems,
take your tractor to an authorized service center for repair
and/or adjustment.
FIG. 28
TO REPLACE FUSE
Replace with 20 amp automotive-type plug-in fuse.
The
fuse holder is located behind the dash.
03075