Poulan PBA195H42LT User Manual - Page 7

CHECK BATTERY See Fig. 3, TO ROLL TRACTOR OFF SKID, See Op, eration for location

Get Poulan PBA195H42LT PDF manuals and user guides View all Poulan PBA195H42LT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

ASSEMBLY INSTALL SEAT (See Fig. 2) Adjust seat before tightening adjustment knob. • Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor. • Pivot seat upward and remove from the cardboard packing. Remove the cardboard packing and discard. • Place seat on seat pan so head of shoulder bolts are positioned over the large slotted holes in pan. • Push down on seat to engage shoulder bolts in slots and pull seat towards rear of tractor. • Pivot seat and pan forward and assemble adjustment knob and flat washer loosely. Do not tighten. • Lower seat into operating position and sit in seat. • Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down. • Get off seat without moving its adjusted position. • Raise seat and tighten adjustment knob securely. SEAT SEAT PAN SHOULDER BOLTS 02617 FLAT WASHER 02615 ADJUSTMENT KNOB FIG. 2 CHECK BATTERY (See Fig. 3) • Lift seat pan to raised position. • If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in MAINTENANCE section of this manual for charging instructions). SEAT PAN LABEL FIG. 3 NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid. WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects. TO ROLL TRACTOR OFF SKID (See Operation section for location and function of controls) • Press lift lever plunger and raise attachment lift lever to its highest position. • Release parking brake by depressing clutch/brake pedal. • Place freewheel control in "transmission disengaged position" (See "TO TRANSPORT" in the Operation section of this manual). • Roll tractor forward off skid. • Remove banding holding the deflector shield up against tractor. 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
7
ASSEMBLY
FIG. 3
CHECK BATTERY (See Fig. 3)
•
Lift seat pan to raised position.
•
If this battery is put into service after month and year
indicated on label (label located between terminals)
charge battery for minimum of one hour at 6-10 amps.
(See "BATTERY" in MAINTENANCE
section of this
manual for charging instructions).
SEAT PAN
LABEL
NOTE:
You may now roll or drive your tractor off the skid.
Follow the appropriate instruction below to remove the
tractor from the skid.
WARNING:
Before starting, read, understand and follow
all instructions in the Operation section of this manual. Be
sure tractor is in a well-ventilated area. Be sure the area in
front of tractor is clear of other people and objects.
TO ROLL TRACTOR OFF SKID
(See Op-
eration section for location and function of
controls)
•
Press lift lever plunger and raise attachment lift lever
to its highest position.
•
Release parking brake by depressing clutch/brake
pedal.
•
Place freewheel control in "transmission disengaged
position" (See “TO TRANSPORT” in the Operation
section of this manual).
•
Roll tractor forward off skid.
•
Remove banding holding the deflector shield up against
tractor.
ADJUSTMENT
KNOB
FLAT WASHER
02615
02617
SEAT PAN
SHOULDER
BOLTS
SEAT
INSTALL SEAT (See Fig. 2)
Adjust seat before tightening adjustment knob.
•
Remove adjustment knob and flat washer securing
seat to cardboard packing and set aside for assembly
of seat to tractor.
•
Pivot seat upward and remove from the cardboard pack-
ing. Remove the cardboard packing and discard.
•
Place seat on seat pan so head of shoulder bolts are
positioned over the large slotted holes in pan.
•
Push down on seat to engage shoulder bolts in slots
and pull seat towards rear of tractor.
•
Pivot seat and pan forward and assemble adjustment
knob and flat washer loosely. Do not tighten.
•
Lower seat into operating position and sit in seat.
•
Slide seat until a comfortable position is reached which
allows you to press clutch/brake pedal all the way
down.
•
Get off seat without moving its adjusted position.
•
Raise seat and tighten adjustment knob securely.
FIG. 2