Poulan PZ4822 User Manual - Page 48

To level deck, Side-to-side adjustment, by moving the deck lift connector to

Get Poulan PZ4822 PDF manuals and user guides View all Poulan PZ4822 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

MAINTENANCE To level deck Adjust the deck while the mower is on a level surface. Make sure the tires are inflated to the correct pressure. See "Technical Data" under Transmission. If tires are under or over inflated, you can not properly adjust your deck. NOTE: It may be easier to adjust the front lift linkages by removing the floor pan before any adjustments are made. Side-to-side adjustment 1. Raise the deck into the four inch 4" (102 mm) cutting position. 2. Measure height from the bottom edge of the deck to the ground at both front corners. Distance "A" should be the same, or within 3/16" (5 mm) of an inch. 3. If adjustment is necessary, make adjustment to one side of the deck only 4. Remove the securing ring from the top pin and the bottom clevis pin. Push bottom clevis pin through deck lift connector while supporting deck. Adjust by moving the deck lift connector to a new hole to lower or raise that specific corner of the deck. The round hole closest to the long slot is the shorter length and will raise the deck, the round hole farthest away from the long slot is the longer of the two and would lower the deck when used. 5. Recheck measurements after adjustment. Distances A 1. Front lift linkage 2. Hex nut Adjustment A CZ-16 8011-645 English-47

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
English-
47
MAINTENANCE
To level deck
Adjust the deck while the mower is on a level
surface. Make sure the tires are inflated to
the correct pressure. See “Technical Data”
under Transmission. If tires are under or over
inflated, you can not properly adjust your
deck.
NOTE:
It may be easier to adjust the front lift
linkages by removing the floor pan before any
adjustments are made.
Side-to-side adjustment
1.
Raise the deck into the four inch 4”
(102 mm) cutting position.
2.
Measure height from the bottom edge of
the deck to the ground at both front
corners. Distance “A” should be the
same, or within 3/16” (5 mm) of an inch.
3.
If adjustment is necessary, make
adjustment to one side of the deck only
4.
Remove the securing ring from the top
pin and the bottom clevis pin. Push
bottom clevis pin through deck lift
connector while supporting deck. Adjust
by moving the deck lift connector to a
new hole to lower or raise that specific
corner of the deck. The round hole
closest to the long slot is the shorter
length and will raise the deck, the round
hole farthest away from the long slot is
the longer of the two and would lower the
deck when used.
5.
Recheck measurements after
adjustment.
CZ-16
Distances A
8011-645
1. Front lift linkage
2. Hex nut
Adjustment A