Poulan PZ4822 User Manual - Page 53

Lubricating the Cables, Lubricating in Accordance with the, Lubrication Schedule

Get Poulan PZ4822 PDF manuals and user guides View all Poulan PZ4822 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

LUBRICATION Lubricating the Cables If possible, grease both ends of the cables and move the controls to end stop positions when lubricating. Refit the rubber covers on the cables after lubrication. Cables with sheaths will bind if they are not lubricated regularly. If a cable binds, it can disrupt operation. If a cable binds, remove the cable and hang it vertically. Lubricate it with light engine oil until the oil begins to escape from the bottom. Tip: Fill a small plastic bag with oil and tape it so that it seals against the sheath and allow the cable to hang vertically from the bag overnight. If you do not succeed in lubricating the cable, it must be replaced. Lubricating in Accordance with the Lubrication Schedule 1. Caster wheels Lubricate with a grease gun. One zerk for each bearing, two strokes. Use only good quality grease. See General in Lubrication. 2. Engine Oil (Briggs & Stratton) Changing the Engine Oil The engine oil should be changed for the first time after 5-8 hours of operation. Thereafter, it shall be changed every 50 hours. WARNING! Engine oil can be very hot if it is drained directly after stopping the engine. Allow the engine to cool somewhat first. Castor wheel zerk 8011-717 English-52

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
English-
52
LUBRICATION
Lubricating the Cables
If possible, grease both ends of the cables and move the controls to end stop positions when lubricating.
Refit the rubber covers on the cables after lubrication. Cables with sheaths will bind if they are not
lubricated regularly. If a cable binds, it can disrupt operation.
If a cable binds, remove the cable and hang it vertically. Lubricate it with light engine oil until the oil begins
to escape from the bottom.
Tip: Fill a small plastic bag with oil and tape it so that it seals against the sheath and allow the cable to hang
vertically from the bag overnight. If you do not succeed in lubricating the cable, it must be replaced.
Lubricating in Accordance with the
Lubrication Schedule
1. Caster wheels
Lubricate with a grease gun. One zerk for
each bearing, two strokes. Use only good
quality grease. See General in Lubrication.
2. Engine Oil (Briggs & Stratton)
Changing the Engine Oil
The engine oil should be changed for the first
time after 5-8 hours of operation. Thereafter,
it shall be changed every 50 hours.
8011-717
Castor wheel zerk
WARNING!
Engine oil can be very hot if it is
drained directly after stopping
the engine. Allow the engine to
cool somewhat first.