ProForm 515 Zlt English Manual - Page 22

Unplug The Power

Page 22 highlights

SYMPTOM: The walking belt slows when walked on a. If an extension cord is needed, use only a 3-conductor, 14-gauge (1 mm2) cord that is no longer than 5 ft. (1.5 m). b. If the walking belt is overtightened, treadmill performance may decrease and the walking belt may become damaged. Remove the key and UNPLUG THE POWER CORD. Using the hex key, turn both idler roller screws counterclockwise, 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each edge of the walking belt 2 to 3 in. (5 to 7 cm) off the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walking belt is properly tightened. b SYMPTOM: The walking belt is not centered between the foot rails IMPORTANT: If the walking belt rubs against the foot rails, the walking belt may become damaged. a. First, remove the key and UNPLUG THE POWER CORD. If the walking belt has shifted to the left, use the hex key to turn the left idler roller screw clockwise 1/2 of a turn; if the walking belt has shifted to the right, turn the left idler roller screw counterclockwise 1/2 of a turn. Be careful not to overtighten the walking belt. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walking belt is centered. a Foot Rail 2-3 in. Foot Rail Idler Roller Screws c. Your treadmill features a walking belt coated with a high performance lubricant. IMPORTANT: Never apply silicone spray or other substances to the walking belt or the walking platform unless instructed to do so by an authorized service representative. Such substances may deteriorate the walking belt and cause excessive wear. If you suspect that the walking belt needs more lubricant, see the back cover of this manual. d. If the walking belt still slows when walked on, see the back cover of this manual. SYMPTOM: The walking belt slips when walked on a. First, remove the key and UNPLUG THE POWER CORD. Using the hex key, turn both idler roller screws clockwise, 1/4 of a turn. When the walking belt is correctly tightened, you should be able to lift each edge of the walking belt 2 to 3 in. (5 to 7 cm) off the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and carefully walk on the treadmill for a few minutes. Repeat until the walking belt is properly tightened. a 22

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28

22
SYMPTOM: The walking belt slows when walked on
a.
If an extension cord is needed, use only a 3-con-
ductor, 14-gauge (1 mm
2
) cord that is no longer
than 5 ft. (1.5 m).
b.
If the walking belt is overtightened, treadmill per-
formance may decrease and the walking belt may
become damaged. Remove the key and
UNPLUG
THE POWER CORD.
Using the hex key, turn both
idler roller screws counterclockwise, 1/4 of a turn.
When the walking belt is properly tightened, you
should be able to lift each edge of the walking belt
2 to 3 in. (5 to 7 cm) off the walking platform. Be
careful to keep the walking belt centered. Then,
plug in the power cord, insert the key, and run the
treadmill for a few minutes. Repeat until the walk-
ing belt is properly tightened.
c.
Your treadmill features a walking belt coated with a
high performance lubricant.
IMPORTANT: Never
apply silicone spray or other substances to
the walking belt or the walking platform unless
instructed to do so by an authorized service
representative. Such substances may deterio-
rate the walking belt and cause excessive wear.
If you suspect that the walking belt needs more
lubricant, see the back cover of this manual.
d.
If the walking belt still slows when walked on, see
the back cover of this manual.
SYMPTOM: The walking belt is not centered
between the foot rails
IMPORTANT: If the walking belt rubs against the
foot rails, the walking belt may become damaged.
a.
First, remove the key and
UNPLUG THE POWER
CORD.
If the walking belt has shifted to the left,
use the hex key to turn the left idler roller screw
clockwise 1/2 of a turn;
if the walking belt has
shifted to the right,
turn the left idler roller screw
counterclockwise 1/2 of a turn. Be careful not to
overtighten the walking belt.
Then, plug in the
power cord, insert the key, and run the treadmill
for a few minutes. Repeat until the walking belt is
centered.
SYMPTOM: The walking belt slips when walked on
a.
First, remove the key and
UNPLUG THE POWER
CORD.
Using the hex key, turn both idler roller
screws clockwise, 1/4 of a turn. When the walk-
ing belt is correctly tightened, you should be able
to lift each edge of the walking belt 2 to 3 in. (5 to
7 cm) off the walking platform. Be careful to keep
the walking belt centered. Then, plug in the power
cord, insert the key, and carefully walk on the
treadmill for a few minutes. Repeat until the walk-
ing belt is properly tightened.
2–3 in.
b
Idler Roller Screws
a
a
Foot
Rail
Foot
Rail