ProForm 520 Trainer Treadmill English Manual - Page 10

Aged When The Power Is Turned On.

Get ProForm 520 Trainer Treadmill PDF manuals and user guides View all ProForm 520 Trainer Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

7. Set the console assembly face down on a soft surface to avoid scratching it. Hold a Handrail (18) near the console assembly. Next, insert the console wire into the hole in the bottom of the Handrail (18) and out of the indicated square hole. If necessary, grip the connector with needlenose pliers only in the area indicated by the arrow (see the inset drawing). Then, attach the ground wire to the Handrail with a Silver Ground Screw (11). Next, set the Handrail (18) on the console assembly. Make sure that no wires are pinched. Finger tighten a Console Bolt (22) with a 1/4" Star Washer (21) into the Handrail, and then start two 3/4" Screws (2) into the Handrail. Tighten the Console Bolt and then the two Screws; do not overtighten the Screws. Attach the other Handrail (not shown) to the console assembly in the same way. Note: There are no wires on the other side. 8. Insert the Upright Wire (28) through a Handrail Spacer (88) as shown. Attach the Handrail Spacer to the Right Upright (36) with a 3/4" Screw (2). Cut the plastic tie and remove the strap from the Upright Wire. Attach the other Handrail Spacer (not shown) to the Left Upright (not shown) as described above. Note: There is not a wire on the left side. 7 Console Wire 18 22 21 2 Square Hole Console Assembly Ground Wire 11 8 88 2 28 Tie 36 Strap 9. While another person holds the Console Base (26) near the right Handrail (18), connect the console wire to the Upright Wire (28). See the inset drawing. The connectors should slide together easily and snap into place. If they do not, turn one connector and try again. IF THE CONNECTORS ARE NOT CONNECTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON. Insert the connectors into the Right Upright (36). Attach the Console Base (26) to the Right Upright (36) and the Left Upright (not shown) with four Handrail Bolts (20) and four Handrail Star Washers (19) (only one side of the treadmill is shown). Start all four Handrail Bolts before tightening any of them. 9 18 36 19 20 19 20 10 26 Console Wire 28 Console Wire 28

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
10
9.
While another person holds the Console Base
(26) near the right Handrail (18), connect the
console wire to the Upright Wire (28).
See the
inset drawing. The connectors should slide
together easily and snap into place.
If they do
not, turn one connector and try again.
IF THE
CONNECTORS ARE NOT CONNECTED
PROPERLY, THE CONSOLE MAY BE DAM-
AGED WHEN THE POWER IS TURNED ON.
Insert the connectors into the Right Upright (36).
Attach the Console Base (26) to the Right
Upright (36) and the Left Upright (not shown)
with four Handrail Bolts (20) and four Handrail
Star Washers (19) (only one side of the treadmill
is shown).
Start all four Handrail Bolts before
tightening any of them.
20
19
36
26
28
20
19
9
Console Wire
7.
Set the console assembly face down on a soft
surface to avoid scratching it. Hold a Handrail
(18) near the console assembly.
Next, insert the console wire into the hole in the
bottom of the Handrail (18) and out of the indi-
cated square hole. If necessary, grip the con-
nector with needlenose pliers
only in the area
indicated by the arrow (see the inset draw-
ing).
Then, attach the ground wire to the
Handrail with a Silver Ground Screw (11).
Next, set the Handrail (18) on the console as-
sembly.
Make sure that no wires are pinched.
Finger tighten a Console Bolt (22) with a 1/4"
Star Washer (21) into the Handrail, and then
start two 3/4" Screws (2) into the Handrail.
Tighten the Console Bolt and then the two
Screws; do not overtighten the Screws.
Attach the other Handrail (not shown) to the
console assembly in the same way.
Note:
There are no wires on the other side.
7
Ground
Wire
Console
Wire
Console
Assembly
Square
Hole
18
22
21
2
11
8.
Insert the Upright Wire (28) through a Handrail
Spacer (88) as shown. Attach the Handrail
Spacer to the Right Upright (36) with a 3/4"
Screw (2). Cut the plastic tie and remove the
strap from the Upright Wire.
Attach the other Handrail Spacer (not
shown) to the Left Upright (not shown) as
described above.
Note: There is not a wire on
the left side.
8
28
36
2
88
Tie
Strap
28
18
Console
Wire