ProForm 590hr Treadmill User Manual - Page 6

Assembly

Get ProForm 590hr Treadmill PDF manuals and user guides View all ProForm 590hr Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

ASSEMBLY Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner. Assembly requires the included hex keys and your own phillips screwdriver cutters , rubber mallet , and adjustable spanner . , wire For help identifying the assembly hardware, refer to the drawings below. Note: The assembly hardware and other small parts are packaged in separate part bags. Do not open the part bags until instructed to do so. (The part bags are not labeled according to the order in which they are to be opened.) If a part is not found in the part bags, check to see if the part has been preassembled. 3/4" Screw (6)-16 1 1/4" Screw (92)-2 1 1/4" Bolt (104)-4 2" Silver Screw (93)-2 Wheel Bolt (107)-2 1" Bolt (71)-2 Wheel Nut (21)-2 1. Open part bag B. Identify the Right Upright (82) (the Left Upright [69] has a large round hole in the location shown). Lay the Right Upright flat, and cut the plastic ties off the lower end. Next, feed the Wire Harness (83) into the bottom of the Right Upright and pull it out of the hole in the top. Note: There may be a tie on the end of the Wire Harness to help you pull it through the hole. Attach the Right Upright (82) to the bracket on the right side of the Base (109) with two 1 1/4" Bolts (104) and two Internal Star Washers (72). (Note: It may be helpful to use a rubber mallet to fully insert the Right Upright into the bracket.) Do not tighten the Bolts yet. Be careful not to damage the Wire Harness. Attach the Left Upright (69) to the left side of the Base (109) in the same way. Note: There is not a wire harness on the left side. 1 Hole Internal Star Washer (72)-6 83 82 69 Bracket 72 104 109 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
6
3/4” Screw (6)–16
Internal Star
Washer (72)–6
1 1/4” Bolt (104)–4
Wheel Bolt (107)–2
Wheel Nut (21)–2
2” Silver Screw (93)–2
1 1/4” Screw (92)–2
1” Bolt (71)–2
For help identifying the assembly hardware, refer to the drawings below. Note: The assembly hardware and other
small parts are packaged in separate part bags.
Do not open the part bags until instructed to do so. (The
part bags are not labeled according to the order in which they are to be opened.) If a part is not found in
the part bags, check to see if the part has been preassembled.
ASSEMBLY
Assembly requires two persons.
Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is
coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the
top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill perfor-
mance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild,
non-abrasive cleaner.
Assembly requires the included hex keys
and your own phillips screwdriver
, wire
cutters
, rubber mallet
,
and adjustable spanner
.
1.
Open part bag B.
Identify the Right Upright (82) (the
Left Upright [69] has a large round hole in the location
shown). Lay the Right Upright flat, and cut the plastic
ties off the lower end. Next, feed the Wire Harness (83)
into the bottom of the Right Upright and pull it out of the
hole in the top. Note: There may be a tie on the end of
the Wire Harness to help you pull it through the hole.
Attach the Right Upright (82) to the bracket on the right
side of the Base (109) with two 1 1/4” Bolts (104) and
two Internal Star Washers (72). (Note: It may be helpful
to use a rubber mallet to fully insert the Right Upright
into the bracket.)
Do not tighten the Bolts yet. Be
careful not to damage the Wire Harness.
Attach the Left Upright (69) to the left side of the
Base (109) in the same way.
Note: There is not a wire
harness on the left side.
82
83
1
69
Hole
109
104
72
Bracket