ProForm J6si Treadmill English Manual - Page 6

Assembly - treadmill parts

Get ProForm J6si Treadmill PDF manuals and user guides View all ProForm J6si Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

ASSEMBLY Assembly requires two people. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Assembly requires the included allen wrench and your own phillips screwdriver , adjustable wrench and scissors . 1. With the help of a second person, carefully raise the treadmill to the upright position. While the other person tips the treadmill to one side and holds it, insert one of the Extension Legs (103) into the treadmill. Make sure that the Extension Leg is turned so the Warning Decal (20) is on top. Tighten two of the four Short Screws (101) into the treadmill and the Extension Leg. Next, tip the treadmill to the other side and attach the other Extension Leg (not shown) in the same way. Lower the side of the treadmill so that both Extension Legs (103) are resting flat on the floor. 1 20 103 101 2. Refer to HOW TO LOWER THE TREADMILL FOR USE on page 14. Follow step 2 to lower the treadmill. Attach the latch support to the center hole in the left Upright (82) with a 3/4Ó Screw (81) as shown. Make sure that the Screw is tight, but do not overtighten it; if the Screw is overtightened, the latch will not slide smoothly. Remove the tape from the Latch Assembly (77). Be careful to hold the parts together. Inset drawings A and B show how the parts fits together. Make sure that the tabs on the latch are touching one side of the bracket and the back end of the latch is flush with the other side of the bracket. Then, insert the two springs into the bracket. Attach the Latch Assembly (77) to the left Upright (82) with two 3/4Ó Screws (81). 3. Cut the plastic tie off the bracket on the base of each Upright (82). Next, cut the plastic tie off the Left Handrail (74). Position the Left Handrail on the left Upright (82). The bracket on the base of the left Upright should be inside of the lower end of the Left Handrail, as shown in the inset drawing. 2 82 77 81 81 Latch Support 3 74 Plastic Tie 82 A Bracket Latch B Spring Flush Spring Tabs 82 Plastic Tie 74 Bracket 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
2.
Refer to HOW TO LOWER THE TREADMILL FOR USE
on page 14. Follow step 2 to lower the treadmill.
Attach the latch support to the center hole in the left Upright
(82) with a 3/4± Screw (81) as shown.
Make sure that the
Screw is tight, but do not overtighten it; if the Screw
is overtightened, the latch will not slide smoothly.
Remove the tape from the Latch Assembly (77).
Be care-
ful to hold the parts together.
Inset drawings A and B
show how the parts fits together. Make sure that the tabs
on the latch are touching one side of the bracket and the
back end of the latch is flush with the other side of the
bracket. Then, insert the two springs into the bracket.
Attach the Latch Assembly (77) to the left Upright (82)
with two 3/4± Screws (81).
77
81
81
82
2
Flush
Bracket
A
B
Latch
Support
Latch
Spring
Spring
Tabs
1.
With the help of a second person, carefully raise the
treadmill to the upright position. While the other person
tips the treadmill to one side and holds it, insert one of the
Extension Legs (103) into the treadmill. Make sure that
the Extension Leg is turned so the Warning Decal (20) is
on top. Tighten two of the four Short Screws (101) into the
treadmill and the Extension Leg.
Next, tip the treadmill to the other side and attach the other
Extension Leg (not shown) in the same way. Lower the
side of the treadmill so that both Extension Legs (103) are
resting flat on the floor.
20
101
103
1
ASSEMBLY
Assembly requires two people.
Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed.
Assembly requires the included allen wrench
and your own phillips screwdriver
, adjustable wrench
and scissors
.
3.
Cut the plastic tie off the bracket on the base of each
Upright (82).
Next, cut the plastic tie off the Left Handrail (74).
Position the Left Handrail on the left Upright (82). The
bracket on the base of the left Upright should be
inside
of the lower end of the Left Handrail, as shown in the
inset drawing.
Plastic
Tie
74
82
Plastic
Tie
82
3
Bracket
74
6