ProForm Style 9000 Uk Manual - Page 22

Troubleshooting

Get ProForm Style 9000 PDF manuals and user guides View all ProForm Style 9000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

TROUBLESHOOTING Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please see the front cover of this manual. PROBLEM: The power does not turn on SOLUTION: a. Make sure that the power cord is plugged into a properly earthed outlet (see page 13). If an extension cord is needed, use only a 3-conductor, 14-gauge (1 mm2 ) cord that is no longer than 5 ft. (1.5 m). Important: The treadmill is not compatible with RCD-equipped outlets. b. After the power cord has been plugged in, make sure that the key is inserted into the console. c. Check the reset/off circuit breaker located on the treadmill frame near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in. PROBLEM: The power turns off during use c Tripped Reset SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in. b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in. c. Remove the key from the console. Reinsert the key into the console. d. If the treadmill still will not run, please see the front cover of this manual. PROBLEM: The displays of the console do not function properly SOLUTION: a. Remove the key from the console and UNPLUG THE POWER CORD. Remove the two 1 1/4" Screws (4) and the two 3/4" Screws (2) and carefully remove the Hood (1). a 4 2 14 Locate the Reed Switch (62) and the Magnet (67) on the left side of the Pulley (64). Turn the Pulley until 1/8 in. the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the 62 64 Reed Switch is about 1/8 in. (3 mm). If necessary, 11 67 loosen the M4 x 110mm Screw (11), move the Reed Switch slightly, and then retighten the Screw. Reattach the Hood (not shown), and run the treadmill for a few minutes to check for a correct speed read- Top View ing. 22

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
22
TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please see the front cover of this manual.
PROBLEM:
The power does not turn on
SOLUTION:
a.
Make sure that the power cord is plugged into a properly earthed outlet (see page 13). If an exten-
sion cord is needed, use only a 3-conductor, 14-gauge (1 mm
2
) cord that is no longer than 5 ft.
(1.5 m). Important: The treadmill is not compatible with RCD-equipped outlets.
b.
After the power cord has been plugged in, make sure that the key is inserted into the console.
c.
Check the reset/off circuit breaker located on the
treadmill frame near the power cord. If the switch
protrudes as shown, the circuit breaker has tripped.
To reset the circuit breaker, wait for five minutes
and then press the switch back in.
PROBLEM:
The power turns off during use
SOLUTION:
a.
Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait
for five minutes and then press the switch back in.
b.
Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c.
Remove the key from the console. Reinsert the key into the console.
d.
If the treadmill still will not run, please see the front cover of this manual.
PROBLEM:
The displays of the console do not function properly
SOLUTION:
a.
Remove the key from the console and
UNPLUG THE
POWER CORD.
Remove the two 1 1/4" Screws (4)
and the two 3/4" Screws (2) and carefully remove the
Hood (1).
Locate the Reed Switch (62) and the Magnet (67) on
the left side of the Pulley (64). Turn the Pulley until
the Magnet is aligned with the Reed Switch.
Make
sure that the gap between the Magnet and the
Reed Switch is about 1/8 in. (3 mm).
If necessary,
loosen the M4 x 110mm Screw (11), move the Reed
Switch slightly, and then retighten the Screw.
Reattach the Hood (not shown), and run the treadmill
for a few minutes to check for a correct speed read-
ing.
1
2
4
4
a
67
62
11
Top
View
1/8 in.
64
Tripped
Reset
c