Pyle PLAD214 PLAD213 Manual 1 - Page 9

Fertures, Controls

Get Pyle PLAD214 PDF manuals and user guides View all Pyle PLAD214 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

FERTURES € CONTROLS 9.Input Mode SWITCH POSITION 112/314 Position MPUT MODE 444 444•4• Ch ALL 1/2/3/4 Bch t on INPUT MODE iN•i44i4A4 Ch V2/3/4 eAcLLn INPUT 6"° I I .., F©ff (Ei )ll It lig Isii IN A OUTPUT 0 +J°'~`- ® 6-,,,, o \,sf , 0 o e O Oo ® ar t:-,,\ o' ,.=.-1 o e eulL1 0 O 10. LED Indicator - POWER : This GREEN LED will illuminate when the amplifier is turned "ON". If it fails to illuminate, check the power connections to the Amplifier and fuses. - PROTECTION : The amplifier protection circuitry will disable the amplifier if input overload, short circuit or extremely high temperature conditions are detected. When the protection mode is in operation, the LED indicator on the side panel will be illuminated, indicating the amplifier has gone into a self preservation mode. If you observe that the Protection LED is lit, please check the system carefully to determine what has caused the protection circuit to engage. The amplifier can be reset by turning the remote power off and then on again. If the amplifier shut down due to a thermal overload condition, please allow it to cool down before restarting. If the amplifier shut down because of an input overload or short circuit, be sure to repair these conditions before attempting to power up the amplifier again. 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
FERTURES
€
CONTROLS
9.Input
Mode
SWITCH
POSITION
INPUT
OUTPUT
112/314
Position
6"°
I
I
0
MPUT
MODE
444
444
4••
Ch
ALL
1/2/3/4
Bch
+
J°
'~`-
®
®
ar
t
:-
,,\
6-
,,
, ,
o
s
\,f ,
0
o
.
',
.=-
.1
t
on
It
..,
i
IN
A
o
o
e
e
INPUT
MODE
•44
iii
N
44
A
Ch
ALL
V2/3/4
ecn
e
ulL
1
0
F©ff
(E
i
ll
)
lig
Isi
O
Oo
O
10.
LED
Indicator
-
POWER
:
This
GREEN
LED
will
illuminate
when
the
amplifier
is
turned
"ON".
If
it
fails
to
illuminate,
check
the
power
connections
to
the
Amplifier
and
fuses.
-
PROTECTION
:
The
amplifier
protection
circuitry
will
disable
the
amplifier
if
input
overload,
short
circuit
or
extremely
high
temperature
conditions
are
detected.
When
the
protection
mode
is
in
operation,
the
LED
indicator
on
the
side
panel
will
be
illuminated,
indicating
the
amplifier
has
gone
into
a
self
preservation
mode.
If
you
observe
that
the
Protection
LED
is
lit,
please
check
the
system
carefully
to
determine
what
has
caused
the
protection
circuit
to
engage.
The
amplifier
can
be
reset
by
turning
the
remote
power
off
and
then
on
again.
If
the
amplifier
shut
down
due
to
a
thermal
overload
condition,
please
al
low
it
to
cool
down
before
restarting.
If
the
amplifier
shut
down
because
of
an
input
overload
or
short
circuit,
be
sure
to
repair
these
conditions
before
attempting
to
power
up
the
amplifier
again.
8