Pyle PLCDBT65MRW User Manual - Page 3

Installation

Get Pyle PLCDBT65MRW PDF manuals and user guides View all Pyle PLCDBT65MRW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 3 highlights

INSTALLATION Notes:  Choose the mounting location where the unit will not interfere with the normal driving function of the driver.  Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly.  Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions.  Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle.  Install the unit where it does not get in the driver's way and cannot injure the passenger if there is a sudden stop, like an emergency stop.  If installation angel exceeds 30°from horizontal, the unit might not give its optimum performance. 30 Be sure you test all connections first, and then follow these steps to install the unit.  Make sure the ignition is turned off, and then disconnect the cable from the vehicle battery's negative (-) terminal.  Disconnect the wire harness and the antenna.  Mount the sleeve by inserting the sleeve into the opening of the dashboard and bend open the tabs located around the sleeve with a screwdriver. Not all tabs will be able to make contact, so examine which ones will be most effective. Bending open the appropriate tabs behind the dashboard to secure the sleeve in place. Dashboard Tabs Screwdriver  Avoid installing the unit where it would be subject to high temperature, such as from direct sunlight, or from hot air, from the heater, or where it would be subject to dust, dirt or excessive vibration. DIN FRONT-MOUNT Installation Opening This unit can be installed in any dashboard having an opening as shown below: 182m m Installing the unit 53m m Sleeve  Reconnect the wire harness and the antenna and be careful not to pinch any wires or cables.  Slide the unit into the sleeve until it locks into place.  To further secure the unit, use the supplied metal strap to secure the back of the unit in place. Use the supplied hardware (Hex Nut (M5mm) and Spring Washer) to attach one end of the strap to the mounting bolt on the back of the unit. If necessary, bend the metal strap to fit your vehicle's mounting area. Then use the supplied hardware (Tapping 3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
3
INSTALLATION
Notes:
Choose the mounting location where
the unit will not interfere with the
normal driving function of the driver.
Before finally installing the unit, connect
the wiring temporarily and make sure it
is all connected up properly and the
unit and the system work properly.
Use only the parts included with the
unit to ensure proper installation. The
use of unauthorized parts can cause
malfunctions.
Consult with your nearest dealer if
installation requires the drilling of holes
or other modifications of the vehicle.
Install the unit where it does not get in
the driver’s way and cannot injure the
passenger if there is a sudden stop, like
an emergency stop.
If installation angel exceeds 30°from
horizontal, the unit might not give its
optimum performance.
Avoid installing the unit where it would
be subject to high temperature, such as
from direct sunlight, or from hot air,
from the heater, or where it would be
subject to dust, dirt or excessive
vibration.
DIN FRONT-MOUNT
Installation Opening
This unit can be installed in any dashboard
having an opening as shown below:
Installing the unit
Be sure you test all connections first, and
then follow these steps to install the unit.
Make sure the ignition is turned off, and
then disconnect the cable from the
vehicle battery’s negative (
-) terminal.
Disconnect the wire harness and the
antenna.
Mount the sleeve by inserting the
sleeve
into
the
opening
of
the
dashboard and bend open the tabs
located around the sleeve with a
screwdriver. Not all tabs will be able to
make contact, so examine which ones
will be most effective. Bending open the
appropriate tabs behind the dashboard
to secure the sleeve in place.
Tabs
Screwdriver
Sleeve
Dashboard
Reconnect the wire harness and the
antenna and be careful not to pinch any
wires or cables.
Slide the unit into the sleeve until it
locks into place.
To further secure the unit, use the
supplied metal strap to secure the back
of the unit in place. Use the supplied
hardware (Hex Nut (M5mm) and Spring
Washer) to attach one end of the strap
to the mounting bolt on the back of the
unit. If necessary, bend the metal strap
to fit your vehicle’s mounting area. Then
use the supplied hardware (Tapping
30
53mm
182mm