Pyle PWD701 User Guide - Page 8

Test System and Adjust Shock Sensor, Adding Transmitters - alarm

Get Pyle PWD701 PDF manuals and user guides View all Pyle PWD701 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

times if a door remains open 10 seconds after arming. If vehicle has delayed dome light, program for 60 seconds. 11. Auxiliary 2. Select Siren/Horn (Default) Horn will sound when alarm is triggered. Select Horn. Horn will sound with arm, disarm, shock sensor warn-away, and trigger. Select Variable. Auxiliary 2 output will be activated for as long as you hold buttons 3, and 4. Select 30 sec. output. Auxiliary 2 output will be activated 30 seconds upon arming system. 12. Not used 13. Ignition Anti-Hijack. Every time Ignition is turned on. Anti-Hijack Function will be activated. 14. Open Door Anti Hijack. Whenever any door is opened with Ignition on. Anti-Hijack Function will be activated. 15. Remote Anti Hijack.When Ignition is on, and Button # 4 is pressed for 3 Seconds. Anti-Hijack Function will be activated. 16. Resets all programs to factory default settings. Test System and Adjust Shock Sensor Arm and disarm system, checking that the siren chirps and parking lights are functioning normally. Make sure that the programmed features are performing correctly, ie.: ignition locks, passive arming, passive locks, etc. Test the doors and hood/trunk inputs (make sure all doors trigger the system, not just the driver's door). Adjust the shock sensor. Arm the system and try starting the vehicle, it should not start. Arm the system and disarm it using the emergency override feature. If programmed for passive arming make sure that the system arms properly. Tie up wire harness, and replace any under dash panels. Make sure the customer has physical knowledge of the location of the valet/override switch. Adding Transmitters To add a new transmitter to the system have the desired transmitters ready and follow the Code Learning sequence. To enter Code Learning Mode: 1. Turn the ignition on, off, on, off and leave on. • The siren will chirp once. 2. Press and hold the Valet switch for 5 seconds. • The siren will chirp 3 times. 3. Press the Lock Button on the transmitter. • The siren will chirp once. 4. Repeat step 3 for each additional transmitter, up to four total transmitters. 5. Turn off the ignition. • The siren will chirp 3 times. NOTE: If a transmitter is lost or stolen, make sure to code all 4 transmitter memory locations. (Example: If only one transmitter is used, repeat step-3 three more times to remove any previously programmed transmitters.) 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
8
times if a door remains open 10 seconds
after arming. If vehicle has delayed dome
light, program for 60 seconds.
11. Auxiliary 2.
Select Siren/Horn
(Default) Horn will sound
when alarm is triggered.
Select Horn.
Horn will sound with arm,
disarm,
shock
sensor
warn-away,
and
trigger.
Select Variable.
Auxiliary 2 output will be
activated for as long as you hold buttons 3,
and 4.
Select 30 sec. output.
Auxiliary 2 output will
be activated 30 seconds upon arming
system.
12. Not used
13. Ignition Anti-Hijack. Every time Ignition
is turned on. Anti-Hijack Function will be
activated.
14. Open Door Anti Hijack. Whenever any
door is opened with Ignition on. Anti-Hijack
Function will be activated.
15. Remote Anti Hijack. When Ignition is on,
and Button # 4 is pressed for 3 Seconds.
Anti-Hijack Function will be activated.
16. Resets all programs to factory default
settings.
Test System and Adjust Shock Sensor
Arm and disarm system, checking that the
siren
chirps
and
parking
lights
are
functioning normally. Make sure that the
programmed
features
are
performing
correctly, ie.: ignition locks, passive arming,
passive locks, etc.
Test the doors and hood/trunk inputs
(make sure all doors trigger the system, not
just the driver’s door).
Adjust the shock sensor.
Arm the system and try starting the vehicle,
it should not start.
Arm the system and disarm it using the
emergency override feature.
If programmed for passive arming make
sure that the system arms properly.
Tie up wire harness, and replace any under
dash panels.
Make sure the customer has physical
knowledge
of
the
location
of
the
valet/override switch.
Adding Transmitters
To add a new transmitter to the system
have the desired transmitters ready and
follow the Code Learning sequence.
To enter Code Learning Mode:
1. Turn the ignition on, off, on, off and
leave on.
•
The siren will chirp once.
2. Press and hold the Valet switch for 5
seconds.
•
The siren will chirp 3 times.
3.
Press the Lock Button on the transmitter.
•
The siren will chirp once.
4. Repeat step 3 for each additional
transmitter,up to four total transmitters.
5.
Turn off the ignition.
•
The siren will chirp 3 times.
NOTE: If a transmitter is lost or stolen, make
sure to code all 4 transmitter memory
locations. (Example: If only one transmitter
is used, repeat step-3 three more times to
remove
any
previously
programmed
transmitters.)