Rheem Warrior DVX Series Use and Care Manual - Page 9

H.U.D. Mobile Home Construction and Safety Standards.

Page 9 highlights

This appliance must be installed in accordance with the Manufactured Home Construction and Safety Standard (Title 24, CFR; Part 3280), the following instructions, local codes and utility company requirements governing the installation of water heaters in manufactured homes (mobile homes), and/or in the absence of local codes, the latest edition of The National Fuel Gas Code, ANSI Z223.1. NOTICE - All sizes of Co-Axial Roof Jack Assembly have an adjustable tilt Roof Flange to accommodate installation on a pitched roof. Maximum roof pitch is 8-12. For roof pitches greater than 8-12 an alternate roof jack can be purchased. NOTICE: 12" Minimum recommended distance from the top of the water heater to the ceiling for servicing the water heater. This water heater complies with Section 3280.707(d) (2) of H.U.D. Mobile Home Construction and Safety Standards. Adjustable Tilt Roof Flange Roof Jack (Purchased Separately) Roof Jack Adjustment Range 2" X 12" See Dimension Table Below Min Secure Strapping provided with the Water Heater around the edge of the top pan and bottom pan by removing screws, place strapping over holes, reinsert screws and attach to wall with S.M. Screws Provided. Roof Flange Roof Ceiling 34° Max. (8 -12 Pitch) Telescopic Vent Connection Pipe (Supplied with Roof Jack) 42° Max. Tilt is available with optional kit. (8 -12 Pitch) Silicone Rubber Seal (Supplied with Roof Jack) Apply silicone sealant to lip of top plenum for a tight seal with outer pipe. Access Door (Right or Left) No Openings Required Floor Bottom Sheathing Co-Axial Roof Jack Sizing Table 34° Max. (8-12 Pitch) Roof Jack Kit Part Number AP14363A AP14363B AP14363C AP14363D AP14363E 42° Max. (10 3/4-12 Pitch) Roof Jack Kit Part Number AP14334A AP14334B AP14334C AP14334D AP14334E Roof Jack Adjustment Range (See Dimesion X) 24 - 37 Inches 33 - 68 Inches 45 - 97 Inches 60 - 130 Inches 72 - 160 Inches Please note that the roof jack shown above is for illustration purposes only and may not resemble the actual unit in your kit. Figure A - Top View of closet. Water Heater Water Connections Strap Screws Water Connections Gas Control (Thermostat) Relief Valve 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28

Co-Axial Roof Jack Sizing Table
Please note that the roof jack shown above is for illustration
purposes only and may not resemble the actual unit in your kit.
This appliance must be installed in accordance with the
Manufactured Home Construction and Safety Standard (Title
24, CFR; Part 3280), the following instructions, local codes and
utility company requirements governing the installation of water
heaters in manufactured homes (mobile homes), and/or in the
absence of local codes, the latest edition of The National Fuel Gas
Code, ANSI Z223.1.
This water heater complies with Section 3280.707(d) (2) of
H.U.D. Mobile Home Construction and Safety Standards.
NOTICE - All sizes of Co-Axial Roof Jack Assembly have an
adjustable tilt Roof Flange to accommodate installation on a pitched
roof. Maximum roof pitch is 8-12.
For roof pitches greater than
8-12 an alternate roof jack can be purchased.
NOTICE: 12” Minimum recommended distance from the top of
the water heater to the ceiling for servicing the water heater.
9
Figure A - Top View of closet.
Water Heater
Water
Connections
Strap
Screws
Gas Control
(Thermostat)
Relief Valve
Water
Connections
Roof Jack
(Purchased Separately)
Roof Flange
Roof
Ceiling
Telescopic Vent Connection Pipe
(Supplied with Roof Jack)
Silicone Rubber Seal
(Supplied with Roof Jack)
Apply silicone sealant to lip of top plenum
for a tight seal with outer pipe.
Access Door (Right or Left)
No Openings Required
Roof Jack
Adjustment Range
Secure Strapping provided with
the Water Heater around the
edge of the top pan and bottom
pan by removing screws, place
strapping over holes, reinsert
screws and attach to wall with
S.M. Screws Provided.
Floor
Bottom Sheathing
12"
Min
X
See Dimension Table Below
2"
42° Max. Tilt is
available with
optional kit.
(8 -12
Pitch)
Adjustable Tilt
Roof Flange
34° Max.
(8 -12
Pitch)
34° Max. (8-12
Pitch) Roof Jack
Kit Part Number
42° Max. (10 3/4-12
Pitch) Roof Jack Kit
Part Number
Roof Jack Adjustment
Range (See Dimesion X)
AP14363A
AP14334A
24 - 37 Inches
AP14363B
AP14334B
33 - 68 Inches
AP14363C
AP14334C
45 - 97 Inches
AP14363D
AP14334D
60 - 130 Inches
AP14363E
AP14334E
72 - 160 Inches