Ricoh P 502 User Guide - Page 43

turns off and the lower LED lights up in yellow, and then release the switch.

Get Ricoh P 502 PDF manuals and user guides View all Ricoh P 502 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

Installing the USB device server • To use the USB device server in an IPv6 environment, it is necessary to change the network settings in an IPv4 environment first. • The machine status does not appear on your computer because the USB device server does not support bidirectional communication. • You cannot set the IP address for the USB device server using the control panel of the machine. • The default administrator password is not specified. It is recommended that you specify the administrator password on the [Maintenance Information] screen by using up to seven alphanumeric characters. • If you forget the IP address of the USB device server or have changed it from its default, follow the procedure below to initialize the USB device server settings: 1. Turn off the main power of the machine. 2. Press and hold the switch on the interface using a pointed tool such as a pen, and turn on the machine. DDE015 3. Both the upper and lower LEDs of the Ethernet port light up. Be sure to check the upper LED turns off and the lower LED lights up in yellow, and then release the switch. • Confirm the IP address of your computer before starting setup. The default IP address for the USB device server is "192.168.100.100", and the default subnet mask is "255.255.255.0". To perform the initial setup of the USB device server, set the IP address for your computer to "192.168.100.XXX" (set XXX to any number, other than 100, from 0 to 255), and the subnet mask to "255.255.255.0". It is recommended to make a note of the current IP address before changing it. 1. Enter "http://192.168.100.100/" in the address bar of the Web to access the setting screen of the machine. 2. Click [Network Settings]. 3. Enter "root" as the user name, and then click [OK]. 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
•
To use the USB device server in an IPv6 environment, it is necessary to change the network settings
in an IPv4 environment first.
•
The machine status does not appear on your computer because the USB device server does not
support bidirectional communication.
•
You cannot set the IP address for the USB device server using the control panel of the machine.
•
The default administrator password is not specified. It is recommended that you specify the
administrator password on the [Maintenance Information] screen by using up to seven
alphanumeric characters.
•
If you forget the IP address of the USB device server or have changed it from its default, follow the
procedure below to initialize the USB device server settings:
1.
Turn off the main power of the machine.
2.
Press and hold the switch on the interface using a pointed tool such as a pen, and turn on the
machine.
DDE015
3.
Both the upper and lower LEDs of the Ethernet port light up. Be sure to check the upper LED
turns off and the lower LED lights up in yellow, and then release the switch.
•
Confirm the IP address of your computer before starting setup. The default IP address for the USB
device server is "192.168.100.100", and the default subnet mask is "255.255.255.0". To
perform the initial setup of the USB device server, set the IP address for your computer to
"192.168.100.XXX" (set XXX to any number, other than 100, from 0 to 255), and the subnet mask
to "255.255.255.0". It is recommended to make a note of the current IP address before changing
it.
1.
Enter "http://192.168.100.100/" in the address bar of the Web to access the setting
screen of the machine.
2.
Click [Network Settings].
3.
Enter "root" as the user name, and then click [OK].
Installing the USB device server
41