Ryobi JS550LK English Manual - Page 16

Plunge Cutting, Warning, To Make A Plunge Cut, Metal Cutting

Get Ryobi JS550LK PDF manuals and user guides View all Ryobi JS550LK manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

OPERATION PLUNGE CUTTING See Figures 15, 16, and 17. WARNING: To avoid loss of control, broken blades, or damage to the material being cut, always use extreme caution when making plunge cuts. We do not recommend plunge cutting on materials other than wood. TO MAKE A PLUNGE CUT  Mark the line of cut clearly on the workpiece. � Set the orbit adjustment to "0". � Tilt the saw forward so that it rests on the front edge of the base and blade will not come in contact with the workpiece when the saw is turned on. � Make sure the blade is inside the area to be cut. � Using high speed, start the saw and slowly lower the blade into the workpiece until the blade cuts through the wood. � Continue lowering the blade into the workpiece until the base rests flat on the work surface, then move the saw forward to complete the opening. � Use only the 7 teeth per inch blade for this type of cut. METAL CUTTING NOTE: The jig saw has to be in the no-orbit mode to cut metals and conduit. Set the orbital adjustment knob to "0". Many kinds of metals can be cut with the saw. Be careful not to twist or bend the blades. Do not force. If the blade chatters or vibrates excessively, use a finer-tooth metal-cutting blade. If blade heats excessively, use lower speed. If blade teeth become filled or clogged when cutting soft metals, such as aluminum, use a coarser-tooth blade or lower speed. We recommend use of oil when cutting metals to keep blades cool, increase cutting action, and prolong blade life. Clamp the work firmly and saw close to the clamping point to eliminate any vibration of the work being cut. When cutting conduit, pipe or angle iron, clamp work in a vise if possible and saw close to the vise. To cut thin sheet materials, "sandwich" the material between hardboard or plywood and clamp the layers to eliminate vibration and material tearing. By doing this, the material will be cut smoothly. Lay out your pattern or line of cut on top of the "sandwich." NOTE: When cutting metal, keep exposed portion of saw bar clean and free of metal chips by wiping frequently with an oily cloth. Use extreme caution in disposing of oily cloth after completion of job to prevent potential fire hazard. 16 Fig. 15 Fig. 16 Fig. 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
16
PLUNGE CUTTING
See Figures 15, 16, and 17.
WARNING:
To avoid loss of control, broken blades, or damage to
the material being cut, always use extreme caution when
making plunge cuts. We do not recommend plunge cut-
ting on materials other than wood.
TO MAKE A PLUNGE CUT
Mark the line of cut clearly on the workpiece.
Set the orbit adjustment to “0”.
Tilt the saw forward so that it rests on the front edge
of the base and blade will not come in contact with the
workpiece when the saw is turned on.
Make sure the blade is inside the area to be cut.
Using high speed, start the saw and slowly lower the
blade into the workpiece until the blade cuts through the
wood.
Continue lowering the blade into the workpiece until the
base rests flat on the work surface, then move the saw
forward to complete the opening.
Use only the 7 teeth per inch blade for this type of cut.
METAL CUTTING
NOTE:
The jig saw has to be in the no-orbit mode to cut met-
als and conduit. Set the orbital adjustment knob to "0".
Many kinds of metals can be cut with the saw. Be careful not
to twist or bend the blades. Do not force. If the blade chat-
ters or vibrates excessively, use a finer-tooth metal-cutting
blade. If blade heats excessively, use lower speed. If blade
teeth become filled or clogged when cutting soft metals, such
as aluminum, use a coarser-tooth blade or lower speed. We
recommend use of oil when cutting metals to keep blades
cool, increase cutting action, and prolong blade life. Clamp
the work firmly and saw close to the clamping point to elimi-
nate any vibration of the work being cut.
When cutting conduit, pipe or angle iron, clamp work in a
vise if possible and saw close to the vise. To cut thin sheet
materials, "sandwich" the material between hardboard or ply-
wood and clamp the layers to eliminate vibration and material
tearing. By doing this, the material will be cut smoothly. Lay
out your pattern or line of cut on top of the "sandwich."
NOTE: When cutting metal, keep exposed portion of saw
bar clean and free of metal chips by wiping frequently with
an oily cloth. Use extreme caution in disposing of oily cloth
after completion of job to prevent potential fire hazard.
OPERATION
Fig. 15
Fig. 16
Fig. 17