Ryobi RY48130 Operation Manual - Page 13

Setting The Parking Brake, Warning, Adjusting The Seat, Setting The Cutting Deck Height, Caution

Get Ryobi RY48130 PDF manuals and user guides View all Ryobi RY48130 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

OPERATION SETTING THE PARKING BRAKE See Figure 3. To set the parking brake:  Fully depress and hold the brake pedal.  Press the parking brake lever all the way down with your right foot  Release the brake pedal.  Release the parking brake lever.  To release the parking brake: depress and release the brake pedal. WARNING: Never leave the mower unattended when the motor is running or with the key in the power switch. Verify that the parking brake is set and the key has been removed. Failure to set the parking brake could cause the mower to move, and leaving the key could allow unauthorized use that could result in serious personal injury. SEAT ADJUSTMENT LEVER Fig. 4 ADJUSTING THE SEAT See Figure 4. Adjust the seat position to ensure you are able to make firm contact with the accelerator and brake pedals before operating the mower. To move the seat:  Turn key to OFF position and set the parking brake.  Sit down on seat and lift the seat adjustment lever.  While holding the lever, slide the seat to the desired ­position.  Release the lever and make sure the seat is locked in position before operating the mower. WARNING: Be sure the seat is locked into place before operating the mower. A seat that is not secure can cause the operator to shift and lose control of the mower and result in possible death or serious personal injury. SETTING THE CUTTING DECK HEIGHT See Figure 5. Before using the mower, raise the deck height to the cutting position best suited for your lawn. NOTE: To prevent scalping the lawn when encountering high spots, the cutting deck wheels should be positioned approximately 1/2 in. off the ground when the mower is at the desired cutting height. When shipped, the cutting deck wheels are set to the 1.5 in. position. DECK HEIGHT ADJUSTMENT LEVER Fig. 5 To adjust the cutting deck height:  Stop the mower and disengage blades.  Turn key to OFF position and set the parking brake.  To raise the cutting deck, grasp the deck height adjustment lever, push left to disengage from slot, move toward the back of the mower, then push right into slot to secure.  To lower the cutting deck, grasp the deck height adjustment lever, push left to disengage from slot, move toward the front of the mower, then push right into slot to secure. CAUTION: Hold the deck height adjustment lever firmly when setting the deck height and only release when it is secure in the desired slot. Quickly letting go of the lever may create a pinching or pulling hazard to the operator's hand. 13 - English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
13 — English
SETTING THE PARKING BRAKE
See Figure 3.
To set the parking brake:
Fully depress and hold the brake pedal.
Press the parking brake lever all the way down with your
right foot
Release the brake pedal.
Release the parking brake lever.
To release the parking brake:
depress and release the
brake pedal.
WARNING:
Never leave the mower unattended when the motor is
running or with the key in the power switch. Verify that
the parking brake is set and the key has been removed.
Failure to set the parking brake could cause the mower
to move, and leaving the key could allow unauthorized
use that could result in serious personal injury.
ADJUSTING THE SEAT
See Figure 4.
Adjust the seat position to ensure you are able to make
firm contact with the accelerator and brake pedals before
operating the mower.
To move the seat:
Turn key to OFF position and set the parking brake.
Sit down on seat and lift the seat adjustment lever.
While holding the lever, slide the seat to the desired
position.
Release the lever and make sure the seat is locked in
position before operating the mower.
WARNING:
Be sure the seat is locked into place before operating the
mower. A seat that is not secure can cause the operator
to shift and lose control of the mower and result in pos-
sible death or serious personal injury.
SETTING THE CUTTING DECK HEIGHT
See Figure 5.
Before using the mower, raise the deck height to the cutting
position best suited for your lawn.
NOTE:
To prevent scalping the lawn when encountering
high spots,
the cutting deck wheels should be positioned
approximately 1/2 in. off the ground when the mower is at
the desired cutting height. When shipped, the cutting deck
wheels are set to the 1.5 in. position.
Fig. 4
DECK HEIGHT
ADJUSTMENT
LEVER
Fig. 5
SEAT ADJUSTMENT LEVER
To adjust the cutting deck height:
Stop the mower and disengage blades.
Turn key to OFF position and set the parking brake.
To raise the cutting deck, grasp the deck height adjust-
ment lever, push left to disengage from slot, move toward
the back of the mower, then push right into slot to secure.
To lower the cutting deck, grasp the deck height adjust-
ment lever, push left to disengage from slot, move toward
the front of the mower, then push right into slot to secure.
CAUTION:
Hold the deck height adjustment lever firmly when setting
the deck height and only release when it is secure in the
desired slot. Quickly letting go of the lever may create a
pinching or pulling hazard to the operator’s hand.
OPERATION