Ryobi TS1144 Operation Manual - Page 14

Assembly

Get Ryobi TS1144 PDF manuals and user guides View all Ryobi TS1144 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

ASSEMBLY UNPACKING This product requires assembly.  Carefully lift miter saw from the carton by the "D" handle and the saw base, and place it on a level work surface. enced the settings, refer to specific procedures explained later in this manual.  If any parts are damaged or missing, please call 1‑800‑525‑2579 for assistance. WARNING: Do not use this product if any parts on the Loose Parts List are already assembled to your product when you unpack it. Parts on this list are not assembled to the product by the manufacturer and require customer installation. Use of a product that may have been improperly assembled could result in serious personal injury.  This saw has been shipped with the saw arm secured in the down position. To release the saw arm, push down on the "D" handle, cut the tie-wrap, and pull out on the lock pin. WARNING: The saw arm is spring loaded. Hold the handle down to prevent it from snapping up when cutting the tie-wrap. Failure to do so could result in possible serious injury.  Lift the saw arm by the "D" handle. Hand pressure should remain on the saw arm to prevent sudden rise upon release of the tie wrap.  Inspect the tool carefully to make sure no breakage or damage occurred during shipping.  Do not discard the packing material until you have carefully inspected and satisfactorily operated the tool.  The saw is factory set for accurate cutting. After ­assembling it, check for accuracy. If shipping has influ- WARNING: If any parts are damaged or missing do not operate this product until the parts are replaced. Use of this product with damaged or missing parts could result in serious personal injury. WARNING: Do not attempt to modify this product or create accessories not recommended for use with this tool. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury. WARNING: Do not connect to power supply until assembly is complete. Failure to comply could result in accidental starting and possible serious personal injury. WARNING: Do not start the compound miter saw without checking for interference between the blade and the miter fence. Damage could result to the blade if it strikes the miter fence during operation of the saw and may result in personal injury. TRACE HOLES AT THESE LOCATIONS FOR HOLE PATTERN SAW BASE 14 - English TRACE HOLES AT THESE LOCATIONS FOR HOLE PATTERN MOUNTING SURFACE Fig. 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
14 - English
enced the settings, refer to specific procedures explained
later in this manual.
If any parts are damaged or missing, please call
1-800-525-2579 for assistance.
WARNING:
If any parts are damaged or missing do not operate this
product until the parts are replaced. Use of this product
with damaged or missing parts could result in serious
personal injury.
WARNING:
Do not attempt to modify this product or create acces-
sories not recommended for use with this tool. Any such
alteration or modification is misuse and could result in a
hazardous condition leading to possible serious personal
injury.
WARNING:
Do not connect to power supply until assembly is com-
plete. Failure to comply could result in accidental starting
and possible serious personal injury.
WARNING:
Do not start the compound miter saw without checking
for interference between the blade and the miter fence.
Damage could result to the blade if it strikes the miter
fence during operation of the saw and may result in
personal injury.
UNPACKING
This product requires assembly.
Carefully lift miter saw from the carton by the “D” handle
and the saw base, and place it on a level work surface.
WARNING:
Do not use this product if any parts on the
Loose Parts
List
are already assembled to your product when you
unpack it. Parts on this list are not assembled to the
product by the manufacturer and require customer instal-
lation. Use of a product that may have been improperly
assembled could result in serious personal injury.
This saw has been shipped with the saw arm secured in
the down position. To release the saw arm, push down
on the “D” handle, cut the tie-wrap, and pull out on the
lock pin.
WARNING:
The saw arm is spring loaded. Hold the handle down to
prevent it from snapping up when cutting the tie-wrap.
Failure to do so could result in possible serious injury.
Lift the saw arm by the “D” handle. Hand pressure should
remain on the saw arm to prevent sudden rise upon re-
lease of the tie wrap.
Inspect the tool carefully to make sure no breakage or
damage occurred during shipping.
Do not discard the packing material until you have care-
fully inspected and satisfactorily operated the tool.
The saw is factory set for accurate cutting. After
assembling it, check for accuracy. If shipping has influ-
ASSEMBLY
Fig. 8
TRACE HOLES
AT THESE
LOCATIONS
FOR HOLE
PATTERN
TRACE HOLES
AT THESE
LOCATIONS
FOR HOLE
PATTERN
SAW
BASE
MOUNTING
SURFACE