Samsung CHG90 User Manual - Page 26

Tidying Up the Connected Cables, Attach the COVER STAND BODY REAR

Get Samsung CHG90 PDF manuals and user guides View all Samsung CHG90 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Tidying Up the Connected Cables : Headphones hanger : Downward : Upward 1 2 Connect the corresponding cables. Arrange the cables against the bend Hang the HOLDER-CABLE in the direction Arrange the cables against their bend Push the COVER STAND BODY REAR in tendency of the cables and pull the cables as shown in the figure. tendency, and then pull them through the the direction as shown in the figure. out of the COVER-REAR SUB grooves. HOLDER-CABLE hangers. When the set height is changed, you need to arrange the cables and pull them through the HOLDER-CABLE hangers again. Remove the COVER STAND BODY REAR by pulling it in the direction as shown in the figure. Place the corresponding cables into the stand-neck holder. Do not stretch the cable. Three cables in one holder is recommended. Attach the COVER STAND BODY REAR in the direction as shown in the figure with the buckles not being exposed. Move down the COVER STAND BODY REAR until it covers the stand neck completely. 11 12 13 Adjust the set height, if required. Open the Headset Hanger by pushing it down. Hang the headset. Rotate and then push up the Headset Hanger in the directions as shown in the figure. Caution Open the COVER-REAR SUB in the direction as shown in the figure. 26

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
26
Tidying Up the Connected Cables
: Headphones hanger
: Downward
: Upward
1
2
Connect the corresponding cables.
Arrange the cables against the bend
tendency of the cables and pull the cables
out of the COVER-REAR SUB grooves.
Hang the HOLDER-CABLE in the direction
as shown in the figure.
Arrange the cables against their bend
tendency, and then pull them through the
HOLDER-CABLE hangers. When the set
height is changed, you need to arrange
the cables and pull them through the
HOLDER-CABLE hangers again.
Push the COVER STAND BODY REAR in
the direction as shown in the figure.
Remove the COVER STAND BODY REAR
by pulling it in the direction as shown in
the figure.
Place the corresponding cables into
the stand-neck holder. Do not stretch
the cable. Three cables in one holder is
recommended.
Attach the COVER STAND BODY REAR in
the direction as shown in the figure with
the buckles not being exposed.
Move down the COVER STAND BODY
REAR until it covers the stand neck
completely.
Adjust the set height, if required.
11
12
13
Open the Headset Hanger by pushing it
down.
Hang the headset.
Rotate and then push up the Headset
Hanger in the directions as shown in the
figure.
Caution
Open the COVER-REAR SUB in the
direction as shown in the figure.