Samsung DMT400RHS Installation Guide Ver.1.0 (English, French, Spanish) - Page 9

Check Water Supply Requirements And Cautions - not draining

Get Samsung DMT400RHS PDF manuals and user guides
UPC - 036725593985
View all Samsung DMT400RHS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

02 INSTALLING THE DISHWASHER STEP 3 CHECK WATER SUPPLY REQUIREMENTS AND CAUTIONS • The hot water supply line pressure must be between 20~120 psi (140~830 kPa). • Adjust the water heater to deliver water between 120 ˚F (49 ˚C) ~ 149 ˚F (65 ˚C). - The dishwasher must be connected to a hot water supply between 120 ˚F (49 ˚C) ~ 149 ˚F (65 ˚C). This temperature range provides the best washing result and shortest cycle time. Temperature should not exceed 149 ˚F (65 ˚C) to prevent damage to dishes. - Ensure that the water supply valve is turned off before connecting the hot water supply line to the dishwasher. - Seal the hot water supply line connections using teflon tape or sealing compound to stop any water leakage. - The hot water supply line must pass through the channel on the bottom of the dishwasher as shown in Figure 2. Do not place the dishwasher on the water supply line. - The drain hose connected to the dishwasher must be run through the hole in the side wall so it can be connected to the drain outlet of the sink. When you install the dishwasher, ensure there is nothing on the drain hose and be careful not to tear it during the installation process. Power cable Hot Water Supply Line 5¹⁄3~7¹⁄3 in. (135 ~ 185mm) Dishwasher bottom installation_DD68-00046A-06_EN_130401.indd Sec3:9 installing the dishwasher _9 2013-04-01 5:05:22

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
installing the dishwasher
_9
02 INSTALLING THE DISHWASHER
STEP 3
CHECK WATER SUPPLY REQUIREMENTS AND CAUTIONS
•
The hot water supply line pressure must be between 20~120 psi (140~830 kPa).
•
Adjust the water heater to deliver water between 120 ˚F (49 ˚C) ~ 149 ˚F (65 ˚C).
-
The dishwasher must be connected to a hot water supply between 120 ˚F (49 ˚C) ~ 149 ˚F
(65 ˚C). This temperature range provides the best washing result and shortest cycle time.
Temperature should not exceed 149 ˚F (65 ˚C) to prevent damage to dishes.
-
Ensure that the water supply valve is turned off
before connecting the hot water supply line to
the dishwasher.
-
Seal the hot water supply line connections using teflon tape or sealing compound to stop any
water leakage.
-
The hot water supply line must pass through the channel on the bottom of the dishwasher as
shown in Figure 2. Do not place the dishwasher on the water supply line.
-
The drain hose connected to the dishwasher must be run through the hole in the side wall so
it can be connected to the drain outlet of the sink. When you install the dishwasher, ensure
there is nothing on the drain hose and be careful not to tear it during the installation process.
<Figure 2>
Hot Water
Supply Line
Dishwasher bottom
Power cable
5¹⁄
3
~7¹⁄
3
in.
(135 ~ 185mm)
installation_DD68-00046A-06_EN_130401.indd Sec3:9
installation_DD68-00046A-06_EN_130401.indd
Sec3:9
2013-04-01
5:05:22
2013-04-01
5:05:22