Samsung DVG50R5400W/A3 User Manual - Page 31

Installation check codes, temperature 41~95 °F 5~35 °C

Get Samsung DVG50R5400W/A3 PDF manuals and user guides View all Samsung DVG50R5400W/A3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

Installation • If the test result displays check code (the duct system is blocked ), refer to the "Ducting requirements" section on page 14 and the "Exhaust ducting guide" section below, and then take proper measures to correct any problems. If the test is suspended, it could result in incorrect results. Follow the proper procedures when testing the dryer. • Even if the test result is normal ("End or 0"), the duct system could be blocked slightly. Properly install all duct work according to the installation instructions in this manual. Installation check codes Check code 0 Clg (Cg) C80 (C8) C90 (C9) Ct tC C1 dC 9C1 Meaning Vent condition is good. The vent is clogged. About 80 % of the vent is clogged. (This may decrease the drying performance.) Over 90 % of the vent is clogged. (This may lead to poor drying performance or cause malfunction) The internal temperature of the dryer is too low (below 32 °F (0 °C)) or too high (over 104 °F (40 °C)) and therefore vent blockage cannot be detected. Temperature sensor error Unit is detecting items inside the drum or there is an error on the dry sensor. Unit is detecting door is open Abnormal voltage detected Solution 1. Clean the lint filter. 2. Check your vent condition. (Refer to the "Ducting requirements" section) * You must take measures (such as cleaning) through expert personnel. Leave the dryer at room temperature (41~95 °F (5~35 °C)) for an hour and check again. Contact a service center. Remove items from the drum and check again. If the problem continues, contact a service center. Close the door properly and check again. If the problem continues, contact a service center. Check the power connection. (Refer to the "Connect the electrical wiring (for electric models)" section) If the problem continues, contact a service center. Untitled-16 31 English 31 2020-07-14 3:36:17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
English
31
Installation
•
If the test result displays check code (the duct system is blocked ), refer to the “
Ducting
requirements
” section on page
14
and the “
Exhaust ducting guide
” section below, and
then take proper measures to correct any problems. If the test is suspended, it could
result in incorrect results. Follow the proper procedures when testing the dryer.
•
Even if the test result is normal (“
End
or
0
”), the duct system could be blocked slightly.
Properly install all duct work according to the installation instructions in this manual.
Installation check codes
Check code
Meaning
Solution
0
Vent condition is good.
Clg (Cg)
The vent is clogged.
1.
Clean the lint filter.
2.
Check your vent condition. (Refer
to the “
Ducting requirements
”
section)
* You must take measures (such as
cleaning) through expert personnel.
C80 (C8)
About 80 % of the vent is clogged.
(This may decrease the drying
performance.)
C90 (C9)
Over 90 % of the vent is clogged.
(This may lead to poor drying
performance or cause malfunction)
Ct
The internal temperature of the
dryer is too low (below 32 °F (0 °C))
or too high (over 104 °F (40 °C)) and
therefore vent blockage cannot be
detected.
Leave the dryer at room
temperature (41~95 °F (5~35 °C))
for an hour and check again.
tC
Temperature sensor error
Contact a service center.
C1
Unit is detecting items inside the
drum or there is an error on the dry
sensor.
Remove items from the drum and
check again.
If the problem continues, contact a
service center.
dC
Unit is detecting door is open
Close the door properly and check
again.
If the problem continues, contact a
service center.
9C1
Abnormal voltage detected
Check the power connection. (Refer
to the “
Connect the electrical wiring
(for electric models)
” section)
If the problem continues, contact a
service center.
Untitled-16
31
2020-07-14
°° 3:36:17