Samsung NA30R5310FS/AA Installation Guide - Page 19

Step 7. Check the ignition of cooktop burners, Step 8. Checking the flame quality, CAUTION

Get Samsung NA30R5310FS/AA PDF manuals and user guides View all Samsung NA30R5310FS/AA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

Step 7. Check the ignition of cooktop burners Check the operation of all cooktop burners after the cooktop has been installed and assembled, gas supply lines have been carefully checked for leaks, and electrical power cord has been plugged in. Lite HI OFF 2 LO 1 MED To turn on a cooktop burner 1. Push in and turn the control knob for that cooktop burner to the Lite position. The "clicking" sound indicates the electronic ignition system is operating properly. The burner will light in about 4 seconds, after the air has been purged from the supply line . 2. After the burner lights, turn the control knob to the desired setting. The "clicking" sound will stop and the flame height will change from Max. to Min. during turning the control knob. 3. Repeat steps 1 and 2 to check the operation of each cooktop burner in succession. NOTE • If the burner does not light within 4 seconds, turn the knob off and wait one minute before trying again. • When you push in and turn the control knob, all spark igniters will make a series of sparks, but only the burner turned to Lite will light. Step 8. Checking the flame quality All combustion flames need to be visually checked to determine their flame quality. CAUTION If you attempt to measure the flame, please use caution. Burns could result. 1. Soft blue flames-Normal for natural gas 1 operation. 2. Yellow tips on outer cones-Normal for LP gas operation. 3. Yellow flames-Abnormal for any gas 2 operation; call for service. NOTE 3 If burner flame looks like 3, the cooktop should not be used until it is serviced. Call for service. Normal burner flames shall look like 1 or 2, depending on the gas type you use. Installation instructions Install_NA30R5310FG_AA_DG68-01133A-00_EN.indd 19 English 19 2019-04-12 12:13:37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
English 19
Installation instructions
Step 7. Check the ignition of cooktop burners
Check the operation of all cooktop burners after the cooktop has been installed
and assembled, gas supply lines have been carefully checked for leaks, and
electrical power cord has been plugged in.
Lite
MED
HI
LO
OFF
2
1
To turn on a cooktop burner
1.
Push in and turn the control knob for that
cooktop burner to the Lite position. The
“clicking” sound indicates the electronic
ignition system is operating properly. The
burner will light in about 4 seconds, after
the air has been purged from the supply
line .
2.
After the burner lights, turn the control
knob to the desired setting. The “clicking”
sound will stop and the flame height will
change from Max. to Min. during turning
the control knob.
3.
Repeat steps 1 and 2 to check the
operation of each cooktop burner in
succession.
NOTE
•
If the burner does not light within 4 seconds, turn the knob off and wait one
minute before
trying again.
•
When you push in and turn the control knob, all spark igniters will make a series
of sparks,
but only the burner turned to Lite will light.
Step 8. Checking the flame quality
All combustion flames need to be visually checked to determine their flame
quality.
CAUTION
If you attempt to measure the flame, please use caution. Burns could result.
2
3
1
1.
Soft blue flames
—Normal for natural gas
operation.
2.
Yellow tips on outer cones
—Normal for
LP gas operation.
3.
Yellow flames
—Abnormal for any gas
operation; call for service.
NOTE
If burner flame looks like 3, the cooktop
should not be used until it is serviced. Call
for service. Normal burner flames shall look
like 1 or 2, depending on the gas type you
use.
Install_NA30R5310FG_AA_DG68-01133A-00_EN.indd
19
2019-04-12
°° 12:13:37