Samsung RFG298AAPN User Manual (user Manual) (ver.0.5) (English) - Page 18

CHECKinG tHE wAtER DisPEnsER LinE, Connecting to the water supply line - help

Get Samsung RFG298AAPN PDF manuals and user guides View all Samsung RFG298AAPN manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Setting up your French Door Refrigerator CHECKinG tHE wAtER DisPEnsER LinE A water dispenser is one of the helpful features on your new refrigerator. To help promote better health, the water filter removes unwanted particles from your water. However, it does not sterilize or destroy microorganisms. You may need to purchase a water purifying system to do that. In order for the ice maker to operate properly, a water pressure of 20~125 psi is required. Under normal conditions, a 170 cc (5.75 oz.) cup can be filled in 10 seconds. If the refrigerator is installed in an area with low water pressure (below 20psi), you can install a booster pump to compensate for the low pressure. Make sure the water storage tank inside the refrigerator is properly filled. To do this, press the water dispenser lever until the water runs from the water outlet. Water line installation kits are available at extra cost from your dealer. We recommend using a water line installation kit that contains copper tubing and ¼" compression nut. Connecting to the water supply line 1. First, shut off the main water supply. 2. L ocate the nearest cold water drinking line and install the pipe clamp and shut off valve. Cold water line Pipe clamp Shut off valve 3. Connect the water line installation kit to shut off valve. Cold water line Pipe clamp Shut off valve Water line installation kit After connecting the water supply with water filter, turn on water supply and Flush 3 gallons through filter before use (flush approximately 6 minutes). If water drop or leakage is found on the connection area, turn off the main water supply. Check it and, if necessary, tighten it more. 18_ Setting Up

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
18_
Setting Up
Setting up your French Door Refrigerator
CHECKING THE WATER DISPENSER LINE
A water dispenser is one of the helpful features on your new refrigerator. To help promote better
health, the water filter removes unwanted particles from your water. However, it does not sterilize or
destroy microorganisms. You may need to purchase a water purifying system to do that.
In order for the ice maker to operate properly, a water pressure of 20~125 psi is required.
Under normal conditions, a 170 cc (5.75 oz.) cup can be filled in 10 seconds.
If the refrigerator is installed in an area with low water pressure (below 20psi), you can install a booster pump to
compensate for the low pressure.
Make sure the water storage tank inside the refrigerator is properly filled. To do this, press the water dispenser
lever until the water runs from the water outlet.
Water line installation kits are available at extra cost from your dealer. We recommend using a water line
installation kit that contains copper tubing and ¼” compression nut.
1.
First, shut off the main water supply.
Connecting to the water supply line
Pipe clamp
Cold water line
Shut off valve
2. Locate the nearest cold water drinking line and install the pipe
clamp and shut off valve.
Shut off valve
Pipe clamp
Cold water line
Water line installation kit
After connecting the water supply with water filter, turn on water supply and
Flush 3 gallons through filter before use (flush approximately 6 minutes).
If water drop or leakage is found on the connection area, turn off the main water supply.
Check it and, if necessary, tighten it more.
3. Connect the water line installation kit to shut off valve.