Samsung TXJ2766 Service Manual - Page 11

Alignment and Adjustments - tv

Get Samsung TXJ2766 PDF manuals and user guides View all Samsung TXJ2766 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Alignment and Adjustments 3. Alignment and Adjustments 3-1 Preadjustment 1. Since there are no VRs in the K51A chassis, all adjustments after parts replacement must be done in the Service Mode. 2. The Factory Mode adjustments are necessary when either the EEPROM (IC902) or the CRT is replaced. 3. Do not tamper with the Ò AdjustmentÓ screen of the Factory Mode menu. This screen is intended only for factory use. 4. WHEN EEPROM (IC902) IS REPLACED (1) When IC902 is replaced, all adjustment data revert to their initial values. It is necessary to re-program this data. (2) After IC902 is replaced, warm up the TV for 10 seconds. Make the following adjustments AFTER setting up purity and convergence: White Balance Sub-Brightness Vertical Center Vertical Size Horizontal Size (No use in 21Ó and 25Ó models) 3-2 Factory ("SERVICE") Mode 1. The set must be in Factory (ÒServiceÓ) Mode. Selection sequence: STAND-BY ® MUTE ® 1 ®8 ® 2 ® POWER ON 2. The Ò FACTORY MODEÓ message will be displayed. The Factory Mode has four components : Adjustment, MPX, PIP, Option Byte and Factory Reset. 3. Access the Adjustment Mode by pressing the ÒVOLUMEÓ keys ( , ) The adjustment parameters are listed in the accompanying table. Select them by pressing the CHANNEL keys (v,w). 4. After completing the Factory Mode adjustments, turn the power switch OFF. w w Samsung Electronics 3-1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
Alignment and Adjustments
Samsung Electronics
3-1
3. Alignment and Adjustments
3-1 Preadjustment
1.
Since there are no VRs in the K51A chassis, all
adjustments after parts replacement must be
done in the Service Mode.
2.
The Factory Mode adjustments are necessary
when either the EEPROM (IC902) or the CRT
is replaced.
3.
Do not tamper with the ° Adjustment± screen
of the Factory Mode menu.
This screen is
intended only for factory use.
4.
WHEN EEPROM (IC902) IS REPLACED
(1)
When IC902 is replaced, all adjustment data
revert to their initial values.
It is necessary to
re-program this data.
(2)
After IC902 is replaced, warm up the TV for
10 seconds.
Make the following adjustments AFTER
setting up purity and convergence:
White Balance
Sub-Brightness
Vertical Center
Vertical Size
Horizontal Size (No use in 21± and 25±
models)
3-2 Factory (“SERVICE”) Mode
1.
The set must be in Factory (°Service±) Mode.
Selection sequence:
STAND-BY
fi
MUTE
fi
1
fi
8
fi
2
fi
POWER ON
2.
The ° FACTORY MODE± message will be displayed.
The Factory Mode
has four components : Adjustment, MPX, PIP, Option Byte and Factory
Reset.
3.
Access the Adjustment Mode by pressing the °VOLUME± keys (
,
)
The adjustment parameters are listed in the accompanying table.
Select them by pressing the CHANNEL keys (
▲
,
▼
).
4.
After completing the Factory Mode adjustments, turn the power switch
OFF.
▼
▼