Samsung WA40J3000AW/A2 User Manual - Page 16

Step 4, Step 5

Get Samsung WA40J3000AW/A2 PDF manuals and user guides View all Samsung WA40J3000AW/A2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

installing your washer STEP 4 Powering your washer Plug the power cord into a 3-prong, well grounded 120 volt 60 Hz approved electrical outlet protected by a 15-amp fuse or comparable circuit breaker. Your washer is grounded through the third prong of the power cord when plugged into a three-prong grounded electrical outlet. Test run Make sure that you have installed your washing machine correctly by running a Rinse+Spin cycle after installation is complete. See Step 5 below. STEP 5 Running a test cycle Run a test cycle as follows to make sure your washer is properly installed. 1. Load about 6 pounds of laundry into the tub. 2. Press the Power button to turn on your washer. 3. Select the Rinse+Spin cycle by turning the Cycle Selector. 4. Press the Start/Pause button to start the test cycle. 5. The washer should not rock or vibrate excessively when water is supplied or when washing or spinning, and should drain well during the spin cycle. - If water leaks while water is being supplied or drained, check the water connections. Refer to Step 2, "Connecting the water supply and drain hoses" on pages 14~15 for instructions. - If the washer rocks and vibrates excessively, level your washer again. Refer to Step 3, "Leveling your washer" on page 15 for instructions. English - 16 8"+@8"+"8@64&3."/6 JOEE

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
English -
16
STEP 4
Powering your washer
Plug the power cord into a 3-prong, well grounded 120 volt 60
Hz approved electrical outlet protected by a 15-amp fuse or
comparable circuit breaker.
Your washer is grounded through the third prong of the power
cord when plugged into a three-prong grounded electrical
outlet.
Test run
Make sure that you have installed your washing machine
correctly by running a
Rinse+Spin
cycle after installation
is complete. See Step 5 below.
STEP 5
Running a test cycle
Run a test cycle as follows to make sure your washer is properly installed.
1.
Load about 6 pounds of laundry into the tub.
2.
Press the Power button to turn on your washer.
3.
Select the Rinse+Spin cycle by turning the Cycle Selector.
4.
Press the Start/Pause button to start the test cycle.
5.
The washer should not rock or vibrate excessively when water is supplied or when washing
or spinning, and should drain well during the spin cycle.
-
If water leaks while water is being supplied or drained, check the water connections. Refer
to Step 2, “Connecting the water supply and drain hoses” on pages 14~15 for instructions.
-
If the washer rocks and vibrates excessively, level your washer again. Refer to Step 3,
“Leveling your washer” on page 15 for instructions.
installing your washer
WA3000J_WA40J3000AW_USER MANUAL_DC68-03520A-09.indd
16
2016/1/12
19:11:59