Samsung WA40J3000AW/A2 User Manual - Page 28

Information Codes - error codes

Get Samsung WA40J3000AW/A2 PDF manuals and user guides View all Samsung WA40J3000AW/A2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

troubleshooting Information codes The Washer may display information codes to help you understand what is occurring with your Washer better. CODE SYMBOL MEANING SOLUTION Hot LED Flashes Lid is open when washer is running. Close the lid tightly and restart the cycle. If the code reappears, call for service. Warm LED Flashes Cold LED Flashes Tap Cold LED Flashes Communication error between SUB PBA and MAIN PBA. A button is not working properly. The Water Level sensor is not working properly. When the Tap Cold LED is flashing, the washer drains for 3 minutes. During this time, the Power button is inoperative. Call for service. Call for service. Call for service. Your Washer has tried to fill but was unsuccessful. Extra Large LED Flashes When the Extra Large LED is flashing, the washer drains for 3 minutes. During this time, the Power button is inoperative. Make sure the water faucets are open all the way. Check for kinked hoses. Check the inlet screens on the fill hoses. If you use a Flood Safety Device, remove the device and connect the water hoses directly to the unit. Large LED Flashes Medium LED Flashes Small LED Flashes Check if the hot water supply hose is connected. You must connect the hot water supply hose because hot water is supplied by the Auto Temperature Control (A.T.C.) function. Your Washer has tried to fill but has not reached the proper water level. When the Large LED is flashing, the washer drains for 3 minutes. During this time, the Power button is inoperative. A fault is detected in the water level sensor. Call for service. Call for service. Your washer is not draining. It can also mean that the unit senses a small clog while draining. Do the following: 1) Turn off the unit and turn it on again. 2) Select only the Spin Cycle. 3) Press the Start/Pause to drain the water. If it still does not drain, call for service. Hot & Warm LEDs flash Unbalanced load prevented your Redistribute the load, and then press the Start/ Washer from spinning. Pause button. English - 28 8"+@8"+"8@64&3."/6 JOEE

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
English -
28
INFORMATION CODES
The Washer may display information codes to help you understand what is occurring with your Washer better.
CODE SYMBOL
MEANING
SOLUTION
Hot LED Flashes
Lid is open when washer is
running.
Close the lid tightly and restart the cycle. If the
code reappears, call for service.
Warm LED
Flashes
Communication error between
SUB PBA and MAIN PBA.
Call for service.
Cold LED
Flashes
A button is not working properly.
Call for service.
Tap Cold LED
Flashes
The Water Level sensor is not
working properly.
When the Tap Cold LED is
flashing, the washer drains for
3 minutes. During this time, the
Power button is inoperative.
Call for service.
Extra Large LED
Flashes
Your Washer has tried to fill but
was unsuccessful.
When the Extra Large LED
is flashing, the washer drains for
3 minutes. During this time, the
Power button is inoperative.
Make sure the water faucets are open all the
way. Check for kinked hoses.
Check the inlet screens on the fill hoses.
If you use a Flood Safety Device, remove the
device and connect the water hoses directly to
the unit.
Check if the hot water supply
hose is connected.
You must connect the hot water supply hose
because hot water is supplied by the Auto
Temperature Control (A.T.C.) function.
Large LED
Flashes
Your Washer has tried to fill but
has not reached the proper water
level.
When the Large LED is
flashing, the washer drains for
3 minutes. During this time, the
Power button is inoperative.
Call for service.
Medium LED
Flashes
A fault is detected in the water
level sensor.
Call for service.
Small LED
Flashes
Your washer is not draining. It can
also mean that the unit senses a
small clog while draining.
Do the following:
1) Turn off the unit and turn it on again.
2) Select only the Spin Cycle.
3) Press the Start/Pause to drain the water.
If it still does not drain, call for service.
Hot & Warm
LEDs flash
Unbalanced load prevented your
Washer from spinning.
Redistribute the load, and then press the Start/
Pause button.
troubleshooting
WA3000J_WA40J3000AW_USER MANUAL_DC68-03520A-09.indd
28
2016/1/12
19:12:02