Sanyo DP50719 Owners Manual - Page 3

CONTENTS IMPORTANT SAFETY INSTRUCTIONS 2 FCC INFORMATION 3 TRADEMARKS 3 THINK GAIA 3 SPECIFICATIONS 3 DISPOSAL 3 PROTECTING THE LCD SCREEN 3 PRECAUTIONS 4 CONTENTS 4 STAND REMOVAL / WALL MOUNTING 5 GETTING STARTED- Remote Control Battery Installation 5 Antenna Connections for off-air or cable 5 Universal Remote Control operation 6 PC CONNECTIONS 7 PC MENU OPERATION 7 BACK PANEL JACKS 8 AUDIO / VIDEO CONNECTIONS 9 POWER CONNECTION / INITIAL CHANNEL SEARCH . .10 ON-SCREEN MENU OPERATION- Chanel Setting 11 Channel Search 11 Channel Scan Memory 11 Setup 12 Menu Language 12 Digital Caption 12 V-Chip 13 Energy Saver 14 Clock Timer 14 Light Sensor 14 Panel Protection 14 HDMI Linking 15 Picture 15 Manual Picture Settings 15 aaSound 16 Manual Sound Settings 16 PHOTO VIEWER 17 WARRANTY 18 PROTECTING THE PLASMA SCREEN The screen can be damaged if it is not maintained properly. Do not use hard objects such as hard cloth or paper. Do not use excessive pressure when cleaning the Plasma screen; excessive pressure can cause permanent discoloration or dark spots. NEVER spray liquids on the screen. HANDLING PRECAUTIONS • Handle by the cabinet only. Never touch the screen when handling. • Handle the Plasma HDTV carefully. Handling by more than two people is recommended. • Handling damage is not covered under warranty. POSITIONING PRECAUTIONS • Place this Plasma HDTV as indicated here. Failure to do so may result in a fire hazard. Allowing the proper amount of space at the top, sides, and rear of the Plasma HDTV cabinet is critical for proper air circulation and cooling of the unit. If the Plasma HDTV is to be built into a compartment or similarly enclosed, these minimum distances must be maintained. • Do not cover the ventilation slots on the Plasma HDTV. Heat build-up can reduce the life of your Plasma HDTV, and can be dangerous. • If Plasma HDTV is not to be used for an extended period of time, unplug it from the power outlet. 4 Need help? www.sanyoctv.com 1-800-877-5032 Minimum space required STAND REMOVAL AND WALL MOUNTING (OPTIONAL) Tools Needed: Phillips screwdriver No. 3 IMPORTANT NOTE: Place HDTV face down on a padded or cushioned surface that is larger than the screen size to protect the screen and finish. Handling by more than two people is recommended. Wall mounting of the HDTV must be performed by a skilled person. 1 Remove four (4) screws from the metal bracket. CAUTION: Hold the stand firmly as you remove the last screw. 2 Carefully remove the stand. GETTING STARTED BATTERY INSTALLATION Install batteries in the remote control ( 2 "AAA", not included) PRECAUTIONS To ensure safe operation, please observe the following precautions: • Replace both batteries at the same time. Do not use a new battery with a used battery. • There's a risk of explosion if a battery is replaced by an incorrect type. • Do not expose the Remote Control unit to moisture or heat. • Be sure to match the "+" and "-" signs on the batteries with marks inside the remote control. 3 Use the screws that are threaded into four (4) of the six (6) inserts on the back of your Plasma HDTV to secure it to a wall mounting kit (not included.) UNIVERSAL standard interface: 480 x 200 and 480 x 360 Mounting screws measurements: M6 Diameter, Length-18mm (max.) ANTENNA CONNECTION FOR OFF-AIR SIGNALS OR CABLE ANTENNA CABLE ANALOG / DIGITAL ANTENNA IN The tuner in this HDTV can receive: • Digital and Analog off air signals from an antenna • Analog or ClearQAM cable channels from a direct Cable TV connection. Need help? www.sanyoctv.com 1-800-877-5032 5