Sanyo PDG-DSU30 Owner's Manual - Page 39

Replacing the lamp - bulb

Get Sanyo PDG-DSU30 - 2500 PDF manuals and user guides
UPC - 086483076596
View all Sanyo PDG-DSU30 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

Appendices Replacing the lamp The projector will detect the lamp life itself. It will show you a warning message Warning: To avoid When you see this message, change the lamp as soon as pos- burns, allow the projector to cool for at least 45 minutes sible. Make sure the projector has been cooled down for at least 45 minutes before changing the lamp. before you replace the lamp! 1 2 3 4 Warning: To reduce the risk of personal injury, do not drop the lamp module or touch the lamp bulb. The bulb may shatter and cause injury if it is dropped. Warning: For continued safety replace with a lamp of the same type. 38 English Lamp Replacing Procedure: 1. Switch off the power to the projector by pressing the "ON/ STAND-BY". 2. Allow the projector to cool down at least 45 minutes. 3. Disconnect the power cable. 4. Use a screwdriver to remove the 2 screws from the cover.  5. Push up and remove the cover. 6. Remove the 2 screws from the lamp module  and pull up the lamp bar.  7. Pull out the lamp module by force.  8. Install the new lamp module by reversing the previous steps. 9. After replacing the lamp, turn on the power, and select the menu ->[Options|Lamp Settings] ->[Lamp Counter Reset] to reset the lamp usage hours. See page 32.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
38
English
Appendices
Replacing the lamp
The projector will detect the lamp life itself.
It will show you a
warning message
When you see this message, change the lamp as soon as pos
-
sible. Make sure the projector has been cooled down for at
least 45 minutes before changing the lamp.
Warning: To avoid
burns, allow the
projector to cool for
at least 45 minutes
before you replace the
lamp!
Warning: To reduce the
risk of personal injury,
do not drop the lamp
module or touch the
lamp bulb. The bulb
may shatter and cause
injury if it is dropped.
Warning: For contin-
ued safety replace with
a lamp of the same
type.
Lamp Replacing Procedure:
1.
Switch off the power to the projector by pressing the “ON/
STAND-BY”.
2.
Allow the projector to cool down at least 45 minutes.
3. Disconnect the power cable.
4.
Use a screwdriver to remove the 2 screws from the cover.
5. Push up and remove the cover.
6.
Remove the 2 screws from the lamp module
and pull up
the lamp bar.
7. Pull out the lamp module by force.
8.
Install the new lamp module by reversing the previous steps.
9.
After replacing the lamp, turn on the power, and select the
menu ->[Options|Lamp Settings] ->[Lamp Counter Reset] to
reset the lamp usage hours. See page 32.
1
2
4
3