Sanyo PLC-XL51 Owner's Manual - Page 50

Standby mode, Power management, On start

Get Sanyo PLC-XL51 - 2700 Lumens PDF manuals and user guides
UPC - 086483072222
View all Sanyo PLC-XL51 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

Setting Standby mode This function is available when operating the projector via network. Normal ....... S upply the power to the network function even after turning off the projector. You can turn on/ off the projector via network, modify network environment, and receive an e-mail about projector status while the projector is powered off. Eco S elect "Eco" when you do not use the projector via network. The projector's network function will stop when turning off the projector. Refer to the owner's manual "Network Setup and Operation." Power management For reducing power consumption as well as maintaining the lamp life, the Power management function turns off the projection lamp when the input signal is interrupted and no button is pressed for a certain period. When the input signal is interrupted and no button is pressed for more than 30 seconds, the timer display with "No signal" appears. The countdown starts to turn off the lamp. Select one of the operations. Ready.........When the lamp has been fully cooled down, the POWER indicator changes to green blinking. In this condition, the projection lamp is turned on if the input signal is reconnected or any button on the remote control is pressed. Shut down...W hen the lamp has been fully cooled down, the power is turned off. Off Power management function is off. Then set the countdown timer with the Point 7 8 buttons. ✔Note: • Factory default is "Ready: 5 min." On start When this function is set to "On," the projector is automatically turned on just by connecting the AC power cord to an outlet. ✔Note: •Be sure to turn the projector off properly (see "Turning Off the Projector" on page 21). If the projector is turned off in the incorrect sequence, the On start function does not operate properly. ✔Note: • When selecting Normal, the cooling fans may be running depending on the temperature inside the projector even if the projector is turned off. Power management Time left before Lamp is off. Press the SELECT button at Power management and this box appears. Select one of three settings with the Point 7 8 buttons, and go to the timer with the Point ed buttons and set time with the Point 7 8 buttons. On start 50

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
50
Setting
Power management
Time left before Lamp is off.
Press the SELECT button
at Power management and
this box appears.
Select
one of three settings with
the Point
7 8
buttons, and
go to the timer with the
Point
ed
buttons and set
time with the Point
7 8
buttons.
Power management
For reducing power consumption as well as maintaining
the lamp life, the Power management function turns off the
projection lamp when the input signal is interrupted and no
button is pressed for a certain period.
When the input signal is interrupted and no button is
pressed for more than 30 seconds, the timer display with
“No signal” appears. The countdown starts to turn off the
lamp.
Select one of the operations.
Ready………When the lamp has been fully cooled down, the
POWER indicator changes to green blinking. In
this condition, the projection lamp is turned on if
the input signal is reconnected or any button on
the remote control is pressed.
Shut down…When the lamp has been fully cooled down, the
power is turned off.
Off………… Power management function is off.
Then set the countdown timer with the Point
7 8
buttons.
✔
Note:
• Factory default is “Ready: 5 min.”
On start
When this function is set to “On,” the projector is
automatically turned on just by connecting the AC power
cord to an outlet.
✔
Note:
•Be sure to turn the projector off properly (see “Turning Off
the Projector” on page 21). If the projector is turned off
in the incorrect sequence, the On start function does not
operate properly.
On start
Standby mode
This function is available when operating the projector via
network.
Normal
.......
Supply the power to the network function even
after turning off the projector. You can turn on/
off the projector via network, modify network
environment, and receive an e-mail about
projector status while the projector is powered
off.
Eco
.............
Select “Eco” when you do not use the projector
via network. The projector’s network function
will stop when turning off the projector.
Refer to the owner’s manual “Network Setup and
Operation.”
✔
Note:
• When selecting Normal, the cooling
fans may be running depending on the
temperature inside the projector even if
the projector is turned off.