Sanyo PLV Z2 Owners Manual - Page 41

To change the code of the projector, To change the code of the remote control

Get Sanyo PLV Z2 - LCD Projector - HD PDF manuals and user guides View all Sanyo PLV Z2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

Lamp mode This function allows you to change brightness of the screen. ···· normal brightness ···· the controlled brightness according with input signal ···· lowers brightness and reduces the lamp power consumption. Lamp mode Remote control This projector has two different remote control codes: Code 1 (initial code) and Code 2. This switching function prevents remote control interference when operating several projectors or video equipment together. When operating the projector in "Code 1", both the projector and the remote control must be switched to "Code 1". To change the code of the projector; Set the remote control code in the Setting Menu to "Code 2". To change the code of the remote control; Press both the MENU and the IMAGE button on the remote control together for over 10 seconds. After changing the code, make sure the remote control operates properly. To return to the initial code (Code 1), repeat the steps above. Factory default Lamp counter reset This function is used to reset the lamp replace counter. When replacing the projection lamp, reset the lamp replace counter by using this function. See page 46 for operation. Factory default This function returns all setting values except for the lamp counter to the factory default settings. Setting Select Factory default and this box appears. Select [Yes] , and the next box appears. Select [Yes] to activate it. NOTE G You can also select a lamp mode with the LAMP MODE (LAMP) button on the remote control. (p12) G When the batteries of the remote control are replaced, the remote control code automatically returns to the initial code (Code 1). 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
41
Setting
This function is used to reset the lamp replace counter.
When
replacing the projection lamp, reset the lamp replace counter by
using this function.
See page 46 for operation.
Lamp counter reset
Remote control
This projector has two different remote control codes: Code 1 (initial
code) and Code 2.
This switching function prevents remote control
interference when operating several projectors or video equipment
together.
When operating the projector in “Code 1”, both the projector and
the remote control must be switched to “Code 1”.
To change the code of the projector;
Set the remote control code in the Setting Menu to “Code 2”.
To change the code of the remote control;
Press both the MENU and the IMAGE button on the remote control
together for over 10 seconds.
After changing the code, make sure the remote control operates
properly.
To return to the initial code (Code 1), repeat the steps above.
Lamp mode
Factory default
This function returns all setting values except for the lamp counter to
the factory default settings.
Select Factory
default and this box
appears.
Select
[Yes] , and the next
box appears.
This function allows you to change brightness of the screen.
···· normal brightness
···· the controlled brightness according with input signal
····
lowers brightness and reduces the lamp power consumption.
Select [Yes] to acti-
vate it.
Lamp mode
Factory default
NOTE
●
You can also select a lamp mode with the LAMP MODE (LAMP) button on
the remote control.
(p12)
●
When the batteries of the remote control are replaced, the remote control
code automatically returns to the initial code (Code 1).