Sanyo PLV Z2 Owners Manual - Page 47

Appendix - owners manual

Get Sanyo PLV Z2 - LCD Projector - HD PDF manuals and user guides View all Sanyo PLV Z2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

Appendix Troubleshooting Before calling your dealer or service center for assistance, check the items below once again. - Make sure you have properly connected the projector to peripheral equipment as described in "Connecting to Video Equipment" and "Connecting to a Computer" on page16 and 17. - Make sure all equipment is connected to AC outlet and the power is turned on. - When you operate the projector with a computer and it does not project an image, restart the computer. Problem: - Try these solutions. No power - Plug the power cord of the projector into the AC outlet. - See if the front cover is open and the POWER indicator lights red. - See if the Main On/Off switch is on. - Wait 90 seconds after the projector is turned OFF when turning the projector back on. The projector can be turned on after the POWER indicator turns red. (See "Turning Off the Projector" on page 18.) - Check the WARNING indicator. If the WARNING indicator lights red, the projector cannot be turned on. (See "Warning Indicator" on page 42.) - Check the projection lamp. (See page 45.) - Check the projector is installed on the flat surface. Image is out of focus. - Adjust focus of the projector. - Provide proper distance between the projector and the projection screen. (See page 14.) - Check the projection lens to see if it needs cleaning. (See page 44.) - Moving the projector from a cool temperature location to a warm temperature location may result in moisture condensation on the projection lens. In such an event, leave the projector OFF and wait until condensation disappears. No image - Check the connection between video equipment or your computer and the projector. - See if the input signal is correctly output from your computer. Some laptop computers may need changing the setting for monitor output when you are connecting a laptop computer. See your computer's owner's manual for setting. - It takes about 30 seconds to display an image after turning on the projector. - See if the selected system is corresponding with video equipment or your computer. - Select correct input source once again through menu operation. - Make sure the temperature is not out of the Operating Temperature (5°C ~ 35°C). Image is Left/Right - Check the Ceiling / Rear item. (See "Setting" on page 40.) reversed. Image is Top/Bottom - Check the Ceiling item. (See "Setting" on page 40.) reversed. Some displays are not seen during the Operation. - Check the Display item. (See "Setting" on page 39 .) 47

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
47
Appendix
Troubleshooting
Before calling your dealer or service center for assistance, check the items below once again.
– Make sure you have properly connected the projector to peripheral equipment as described in “Connecting to Video
Equipment” and "Connecting to a Computer" on
page16 and 17.
–
Make sure all equipment is connected to AC outlet and the power is turned on.
–
When you operate the projector with a computer and it does not project an image, restart the computer.
No power
–
Plug the power cord of the projector into the AC outlet.
–
See if the front cover is open and the POWER indicator lights red.
–
See if the Main On/Off switch is on.
– Wait 90 seconds after the projector is turned OFF when turning the projector back on.
The projector can be turned on after the POWER indicator turns red.
(See “Turning Off
the Projector” on page 18.)
–
Check the WARNING indicator.
If the WARNING indicator lights red, the projector cannot
be turned on.
(See "Warning Indicator" on page 42.)
–
Check the projection lamp.
(See page 45.)
–
Check the projector is installed on the flat surface.
Image is out of focus.
–
Adjust focus of the projector.
–
Provide proper distance between the projector and the projection screen.
(See page 14.)
–
Check the projection lens to see if it needs cleaning.
(See page 44.)
–
Moving the projector from a cool temperature location to a warm temperature location
may result in moisture condensation on the projection lens.
In such an event, leave the
projector OFF and wait until condensation disappears.
Image is Left/Right
reversed.
–
Check the Ceiling / Rear item.
(See “Setting” on page 40.)
Problem:
–
Try these solutions.
Image is Top/Bottom
reversed.
–
Check the Ceiling item.
(See “Setting” on page 40.)
Some displays are not
seen during the
Operation.
–
Check the Display item.
(See “Setting” on page 39 .)
No image
–
Check the connection between video equipment or your computer and the projector.
–
See if the input signal is correctly output from your computer.
Some laptop computers
may need changing the setting for monitor output when you are connecting a laptop
computer.
See your computer’s owner’s manual for setting.
–
It takes about 30 seconds to display an image after turning on the projector.
–
See if the selected system is corresponding with video equipment or your computer.
–
Select correct input source once again through menu operation.
–
Make sure the temperature is not out of the Operating Temperature (5°C ~ 35°C).