Sanyo XU105 Instruction Manual, PLC-XU105 - Page 60

Power management does not, after turning off power.

Get Sanyo XU105 - PLC XGA LCD Projector PDF manuals and user guides
UPC - 086483071386
View all Sanyo XU105 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

Appendix No image - Check the connection between your computer or video equipment and the projector. See pages 16-18. - See if the input signal is correctly output from your computer. Some laptop computers may need to change the setting for monitor output when connecting to a projector. See your computer's instruction manual for the setting. - It takes about 30 seconds to display an image after turning on the projector. See page 19. - Check the Input signal, color system, video system or computer system mode. - Make sure the temperature is not out of the specified Operating Temperature (41˚F-95˚F [5˚C-35˚C]). - When "No Show" is operating, the image cannot be displayed. Press the NO SHOW button or any other button on the remote control. No sound - Check the audio cable connection from audio input source. - Adjust the audio source. - Press the Volume + button. See page 24. - Press the Mute button. See page 24 - When the AUDIO OUT is plugged-in, the projector's built-in speaker is not available - Is the image projected? You will hear the sound only when the image is projected. The color is strange. - Check the Input signal, color system,video system or computer system mode. - Make sure the "Blackboard" is not selected on Image select menu.(see page 32,39) Some displays are not seen during the operation. - Check the Display function. See page 44. Auto PC adjustment function - Check the Input signal. Auto PC function can not work when does not work. 480p,575p.720p,480i,575i,1035i or 1080i is selected. (see Page 31 The setting does not remain - Make sure you selected "Store" after adjusting setting. Some settings after turning off power. can not be stored if not registered with "Store".(see page 41) Power management does not work. - Power management function can not work while "Freeze" or "No Show" function is running.(see page 25,26) Capture function does not work. - Check the connection and the input signal to see if there is signal. Auto setup does not work properly. - Make sure "Off" is not selected at the Auto setup function.(see page 43) - Make sure "On" is not selected at the Ceiling function.(see page 47) Auto keystone function does not work even when the projector is tipped. - Make sure the Auto keystone function is not set to "Manual". Press the AUTO SET UP button on the top control.(see page 23,43) 60

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
60
Appendix
No image
– Check the connection between your computer or video equipment
and the projector. See pages 16-18.
– See if the input signal is correctly output from your computer. Some
laptop computers may need to change the setting for monitor output
when connecting to a projector. See your computer’s instruction
manual for the setting.
– It takes about 30 seconds to display an image after turning on the
projector. See page 19.
– Check the Input signal, color system, video system or computer
system mode.
– Make sure the temperature is not out of the specified Operating
Temperature (
41˚F–95˚F [5˚C–35˚C])
.
– When "No Show" is operating, the image cannot be displayed. Press
the NO SHOW button or any other button on the remote control.
No sound
– Check the audio cable connection from audio input source.
– Adjust the audio source.
– Press the Volume + button. See page 24.
– Press the Mute button. See page 24.
– When the AUDIO OUT is plugged-in, the projector's built-in speaker
is not available
– Is the image projected? You will hear the sound only when the image
is projected.
The color is strange.
– Check the Input signal, color system,video system or computer
system mode.
– Make sure the "Blackboard" is not selected on Image select
menu.(see page 32,39)
Some displays are not seen
– Check the Display function. See page 44.
during the operation.
Auto PC adjustment function
– Check the Input signal. Auto PC function can not work when
does not work.
480p,575p.720p,480i,575i,1035i or 1080i is selected.
(see Page 31)
The setting does not remain
– Make sure you selected "Store" after adjusting setting. Some settings
after turning off power.
can not be stored if not registered with "Store".(see page 41)
Power management does not
– Power management function can not work while "Freeze" or "No
work.
Show" function is running.
(see page 25,26)
Capture function does not work.
– Check the connection and the input signal to see if there is signal.
Auto setup does not work properly.
– Make sure "Off" is not selected at the Auto setup function.(see page
43)
– Make sure "On" is not selected at the Ceiling function.(see page 47)
Auto keystone function does not
– Make sure the Auto keystone function is not set to "Manual". Press
work even when the projector is
the AUTO SET UP button on the top control.(see page 23,43)
tipped.