Schwinn 220 Recumbent Bike Assembly and Owner's Manual - Page 33

Console Setup Mode

Get Schwinn 220 Recumbent Bike PDF manuals and user guides View all Schwinn 220 Recumbent Bike manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

CONSOLE SETUP MODE The Console Setup Mode lets you set the units of measure to either English or Metric, change the machine type, or see maintenance statistics (Error Log and Run Hours - for service technician use only). 1. Hold down the Increase button and Decrease button together for 3 seconds while in the POWER-UP MODE to go into the CONSOLE SETUP MODE. Note: Push STOP to go back to the previous screen or the Power-Up Mode screen. 2. The Console display shows the Units prompt. Push START/ENTER to start Units option. Push the Increase/Decrease buttons to change between "Miles-Lb" (English units) and "Km-Kg" (metric units). Note: If the units change when there is data in User Statistics, the statistics change to the new units. 3. Push START/ENTER to set. 4. The Console display shows the Machine Type prompt. Push START/ENTER to start Machine Type option. Push the Increase/Decrease buttons to change between ELLIPTICAL and BIKE. 5. Push START/ENTER to set. 6. The Console display shows the Error Log prompt. Push START/ENTER to start Error Log option. The Error Log stores the last 10 errors (error type and system time of error), listed newest to oldest. Push the Increase/Decrease buttons to move through the Error Log. If there are no errors, the Console display shows "Index=0". 7. Push STOP to exit. 8. The Console shows the RUN HOURS prompt. Push START/ENTER to see total hours for the machine. 9. Push STOP to exit. 10. The Console display shows the Units prompt again. Push STOP to go back to the Power-Up Mode screen. 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
33
The Console Setup Mode lets you set the units of measure to either English or Metric, change the
machine type, or see maintenance statistics (Error Log and Run Hours – for service technician use
only).
1.
Hold down the Increase button and Decrease button together for 3 seconds while in the
POWER-UP MODE to go into the CONSOLE SETUP MODE.
Note:
Push STOP to go back to the previous screen or the Power-Up Mode screen.
2.
The Console display shows the Units prompt. Push START/ENTER to start Units option. Push
the Increase/Decrease buttons to change between “Miles-Lb” (English units) and “Km-Kg”
(metric units).
Note:
If the units change when there is data in User Statistics, the statistics change to the new
units.
3.
Push START/ENTER to set.
4.
The Console display shows the Machine Type prompt. Push START/ENTER to start Machine
Type option. Push the Increase/Decrease buttons to change between ELLIPTICAL and BIKE.
5.
Push START/ENTER to set.
6.
The Console display shows the Error Log prompt. Push START/ENTER to start Error Log
option. The Error Log stores the last 10 errors (error type and system time of error), listed
newest to oldest. Push the Increase/Decrease buttons to move through the Error Log. If there
are no errors, the Console display shows “Index=0”.
7.
Push STOP to exit.
8.
The Console shows the RUN HOURS prompt. Push START/ENTER to see total hours for the
machine.
9.
Push STOP to exit.
10.
The Console display shows the Units prompt again. Push STOP to go back to the Power-Up
Mode screen.
CONSOLE SETUP MODE