Schwinn Network 3.0 Schwinn Owner's Manual - Page 61

Quick Release Levers, Reflectors bicycles over 16

Get Schwinn Network 3.0 PDF manuals and user guides View all Schwinn Network 3.0 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

+/- 5 degrees of verƟcal Quick Release Levers It is important to check the quick release levers before every ride to ensure all connections are made properly and securely. Periodically, disassemble the mechanism from the bicycle and inspect for any wear or damage and replace if necessary. When reinstalling, it is very important to ensure the connections are made properly. (Please refer to p. 29-30 for the appropriate assembly instructions.) Reflectors (bicycles over 16") Your bicycle is supplied with one front (white), one rear (red), two wheel (white), and four pedal (orange) reflectors. These are an important safety and legal requirement, and should remain securely fitted and in good, clean conditions at all times. Periodically, inspect all reflectors, brackets and mounting hardware for signs of wear or damage. Replace immediately if damage is found. Front and rear reflectors should be adjusted to within 5 degrees of vertical. This is measured by looking at the bicycle from the side while it is on flat ground. If the reflectors are out of line, adjust as necessary and be sure all fasteners are tight. (Fig. 4.20, 4.21) 4.20 MAINTENANCE 4.21 60 ©2010

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
©2010
Quick Release Levers
It is important to check the quick release levers before every ride to ensure all connec°ons
are made properly and securely. Periodically, disassemble the mechanism from the
bicycle and inspect for any wear or damage and replace if necessary. When reinstalling,
it is very important to ensure the connec°ons are made properly. (Please refer to
p. 29-30 for the appropriate assembly instruc°ons.)
Reflectors (bicycles over 16”)
Your bicycle is supplied with one front (white), one rear (red), two wheel (white), and
four pedal (orange) reflectors. These are an important safety and legal requirement,
and should remain securely fi±ed and in good, clean condi°ons at all °mes. Periodically,
inspect all reflectors, brackets and moun°ng hardware for signs of wear or damage.
Replace immediately if damage is found. Front and rear reflectors should be adjusted
to within 5 degrees of ver°cal. This is measured by looking at the bicycle from the side
while it is on flat ground. If the reflectors are out of line, adjust as necessary and be
sure all fasteners are °ght. (Fig. 4.20, 4.21)
MAINTENANCE
4.21
+/–
5 degrees
of ver°cal
4.20
60