Home » Seagate Manuals » Hard Drives » Seagate Pipeline HD » Manual Viewer

Seagate Pipeline HD Pipeline HD.2 Series SATA Product Manual - Page 9

Drive specifications

View all Seagate Pipeline HD manuals

Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

2.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate the following drive model: ST31000424CS ST31000322CS ST3500414CS ST3500312CS ST3320413CS ST3320311CS ST3250412CS ST3250312CS ST3160316CS 2.1 Specification summary tables The specifications listed in the following tables are for quick reference. For details on specification measurement or definition, refer to the appropriate section of this manual. Pipeline HD.2 Series SATA Product Manual, Rev. G 3

Section	Page
1.0 Introduction	7
1.1 About the Serial ATA interface	8
2.0 Drive specifications	9
2.1 Specification summary tables	9
2.2 Formatted capacity	16
2.2.1 LBA mode	16
2.3 Default logical geometry	16
2.4 Recording and interface technology	16
2.5 Physical characteristics	17
2.6 Seek time	17
2.7 Start/stop times	17
2.8 Power specifications	18
2.8.1 Power consumption	18
2.8.1.1 Typical current profiles	19
2.8.2 Conducted noise	19
2.8.3 Voltage tolerance	19
2.8.4 Power management modes	20
2.9 Environmental specifications	21
2.9.1 Drive case temperature	21
2.9.2 Temperature gradient	21
2.9.3 Humidity	21
2.9.3.1 Relative humidity	21
2.9.3.2 Wet bulb temperature	21
2.9.4 Altitude	21
2.9.5 Shock	22
2.9.5.1 Operating shock	22
2.9.5.2 Non-operating shock	22
2.9.6 Vibration	22
2.9.6.1 Operating vibration	22
2.9.6.2 Non-operating vibration	22
2.10 Acoustics emissions	23
2.11 Electromagnetic immunity	23
2.12 Reliability	24
2.12.1 Annualized Failure Rate (AFR)	24
2.13 Agency certification	24
2.13.1 Safety certification	24
2.13.2 Electromagnetic compatibility	24
2.13.3 FCC verification	25
2.14 Environmental protection	26
2.14.1 European Union Restriction of Hazardous Substances (RoHS) Directive	26
2.14.2 China Restriction of Hazardous Substances (RoHS) Directive	26
2.15 Corrosive environment	26
3.0 Configuring and mounting the drive	27
3.1 Handling and static-discharge precautions	27
3.2 Configuring the drive	28
3.3 Serial ATA cables and connectors	28
3.4 Drive mounting	29
4.0 Serial ATA (SATA) interface	31
4.1 Hot-Plug compatibility	31
4.2 Serial ATA device plug connector pin definitions	32
4.3 Supported ATA commands	33
4.3.1 Identify Device command	35
4.3.2 Set Features command	39
4.3.3 S.M.A.R.T. commands	40
5.0 Seagate Technology support services	41
Index	43
A	43
B	43
C	43
D	43
E	43
F	43
G	43
H	43
I	43
K	44
L	44
M	44
N	44
O	44
P	44
Q	44
R	44
S	44
T	45
U	45
V	45