Seagate ST33000651SS Constellation ES.2 SAS Product Manual - Page 37

Constellation ES.2 SAS Product Manual, Rev. C

29

7.5.3

Effective altitude (sea level)

a. Operating

–1000 to +10,000 feet (–304.8 to +3,048 meters)

b. Non-operating

–1000 to +40,000 feet (–304.8 to +12,192 meters)

7.5.4

Shock and vibration

Shock and vibration limits specified in this document are measured directly on the drive chassis. If the drive is

installed in an enclosure to which the stated shock and/or vibration criteria is applied, resonances may occur

internally to the enclosure resulting in drive movement in excess of the stated limits. If this situation is apparent,

it may be necessary to modify the enclosure to minimize drive movement.

The limits of shock and vibration defined within this document are specified with the drive mounted by any of

the four methods shown in Figure 5, and in accordance with the restrictions of Section 11.3.

7.5.4.1

Shock

a. Operating—normal

The drive, as installed for normal operation, shall operate error free while subjected to intermittent shock not

exceeding 70 Gs (read) and 40 Gs (write) at a maximum duration of 2ms (half sinewave). Shock may be

applied in the X, Y, or Z axis. Shock is not to be repeated more than once every 2 seconds.

b. Operating—abnormal

Equipment, as installed for normal operation, does not incur physical damage while subjected to

intermittent shock not exceeding 40 Gs at a maximum duration of 11ms (half sinewave). Shock occurring at

abnormal levels may promote degraded operational performance during the abnormal shock period.

Specified operational performance will continue when normal operating shock levels resume. Shock may

be applied in the X, Y, or Z axis. Shock is not to be repeated more than once every 2 seconds.

c. Non-operating

The limits of non-operating shock shall apply to all conditions of handling and transportation. This includes

both isolated drives and integrated drives.

The drive subjected to nonrepetitive shock not exceeding 80 Gs at a maximum duration of 11ms (half

sinewave) shall not exhibit device damage or performance degradation. Shock may be applied in the X, Y,

or Z axis.

The drive subjected to nonrepetitive shock not exceeding 300 Gs at a maximum duration of 2ms (half

sinewave) does not exhibit device damage or performance degradation. Shock may be applied in the X, Y,

or Z axis.

The drive subjected to nonrepetitive shock not exceeding 200 Gs at a maximum duration of 0.5ms (half

sinewave) does not exhibit device damage or performance degradation. Shock may be applied in the X, Y,

or Z axis.

Section	Page
1.0 Seagate Technology support services	9
2.0 Scope	10
3.0 Applicable standards and reference documentation	11
3.1 Standards	11
3.1.1 Electromagnetic compatibility	11
3.1.1.1 Electromagnetic susceptibility	11
3.1.2 Electromagnetic compliance	12
3.1.3 European Union Restriction of Hazardous Substances (RoHS)	13
3.1.4 China Restriction of Hazardous Substances (RoHS) Directive	13
3.2 Reference documents	14
4.0 General description	15
4.1 Standard features	16
4.2 Media description	16
4.3 Performance	16
4.4 Reliability	17
4.5 Formatted capacities	17
4.6 Programmable drive capacity	17
4.7 Factory-installed options	17
5.0 Performance characteristics	18
5.1 Internal drive characteristics	18
5.2 Seek performance characteristics	18
5.2.1 Access time	18
5.2.2 Format command execution time for 512-byte sectors (minutes)	19
5.2.3 General performance characteristics	19
5.3 Start/stop time	19
5.4 Prefetch/multi-segmented cache control	20
5.5 Cache operation	20
5.5.1 Caching write data	21
5.5.2 Prefetch operation	21
6.0 Reliability specifications	22
6.1 Error rates	22
6.1.1 Recoverable Errors	22
6.1.2 Unrecoverable Errors	22
6.1.3 Seek errors	23
6.1.4 Interface errors	23
6.2 Reliability and service	23
6.2.1 Annualized Failure Rate (AFR) and Mean Time Between Failure (MTBF)	23
6.2.2 Preventive maintenance	23
6.2.3 Hot plugging the drive	23
6.2.4 S.M.A.R.T.	24
6.2.5 Thermal monitor	25
6.2.6 Drive Self Test (DST)	26
6.2.6.1 DST failure definition	26
6.2.6.2 Implementation	26
6.2.7 Product warranty	28
7.0 Physical/electrical specifications	29
7.1 PowerChoiceTM power management	29
7.1.1 PowerChoice reporting methods	30
7.2 AC power requirements	30
7.3 DC power requirements	30
7.3.1 Conducted noise immunity	32
7.3.2 Power sequencing	32
7.3.3 Current profiles	33
7.4 Power dissipation	34
7.5 Environmental limits	36
7.5.1 Temperature	36
7.5.2 Relative humidity	36
7.5.3 Effective altitude (sea level)	37
7.5.4 Shock and vibration	37
7.5.4.1 Shock	37
7.5.4.2 Vibration	39
7.5.5 Acoustics	39
7.5.6 Air cleanliness	39
7.5.7 Corrosive environment	39
7.5.8 Electromagnetic susceptibility	40
7.6 Mechanical specifications	41
8.0 About FIPS	42
9.0 About self-encrypting drives	43
9.1 Data encryption	43
9.2 Controlled access	43
9.2.1 Admin SP	43
9.2.2 Locking SP	43
9.2.3 Default password	44
9.3 Random number generator (RNG)	44
9.4 Drive locking	44
9.5 Data bands	44
9.6 Cryptographic erase	44
9.7 Authenticated firmware download	45
9.8 Power requirements	45
9.9 Supported commands	45
9.10 RevertSP	45
10.0 Defect and error management	46
10.1 Drive internal defects/errors	46
10.2 Drive error recovery procedures	46
10.3 SAS system errors	47
10.4 Background Media Scan	47
10.5 Media Pre-Scan	48
10.6 Deferred Auto-Reallocation	48
10.7 Idle Read After Write	48
10.8 Protection Information (PI)	49
10.8.1 Levels of PI	49
10.8.2 Setting and determining the current Type Level	49
10.8.3 Identifying a Protection Information drive	49
11.0 Installation	50
11.1 Drive orientation	50
11.2 Cooling	51
11.3 Drive mounting	52
11.4 Grounding	52
12.0 Interface requirements	53
12.1 SAS features	53
12.1.1 task management functions	53
12.1.2 task management responses	53
12.2 Dual port support	54
12.3 SCSI commands supported	55
12.3.1 Inquiry data	59
12.3.2 Mode Sense data	59
12.4 Miscellaneous operating features and conditions	62
12.4.1 SAS physical interface	63
12.4.2 Physical characteristics	66
12.4.3 Connector requirements	66
12.4.4 Electrical description	66
12.4.5 Pin descriptions	66
12.4.6 SAS transmitters and receivers	67
12.4.7 Power	67
12.5 Signal characteristics	67
12.5.1 Ready LED Out	67
12.5.2 Differential signals	68
12.6 SAS-2 Specification Compliance	68
12.7 Additional information	68
Numerics	69
A	69
B	69
C	69
D	69
E	70
F	70
G	70
H	70
I	70
J	70
K	70
L	71
M	71
N	71
O	71
P	71
Q	72
R	72
S	72
T	72
U	73
V	73
W	73

Seagate ST33000651SS Constellation ES.2 SAS Product Manual - Page 37

Effective altitude sea level, Shock and vibration, 5.4.1, Shock

Page 37 highlights