Home » Seagate Manuals » Hard Drives » Seagate ST800FM0022 » Manual Viewer

Seagate ST800FM0022 Pulsar Serial ATA Product Manual - Page 7

Introduction

View all Seagate ST800FM0022 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate PulsarTM model drives: ST9200011FS ST9100011FS ST950011FS These drives provide the following key features: • Single Layer Cell (SLC) NAND Flash storage. • High instantaneous (burst) data-transfer rates (up to 300MB/s). • Parallel flash access channels. • State-of-the-art on-the-fly error-correction algorithms. • Native Command Queueing with command ordering to increase performance in demanding applications. • Highly integrated hardware functions. • Power loss data protection. • Data Set Management with Trim Support. • Silent operation. • SeaTools diagnostic software performs a drive self-test that eliminates unnecessary drive returns. • Support for S.M.A.R.T. drive monitoring and reporting. • Supports latching SATA cables and connectors. • Worldwide Name (WWN) capability uniquely identifies the drive. Pulsar Product Manual, Rev. A 1

Section	Page
1.0 Introduction	7
1.1 About the Serial ATA interface	8
2.0 Drive specifications	9
2.1 Specification summary tables	9
2.2 Formatted capacity	11
2.2.1 LBA mode	11
2.3 Default logical geometry for ATA based systems	11
2.4 Performance, Recording and interface technology	11
2.4.1 Interface technology	11
2.4.2 Recording technology	11
2.4.3 Performance	12
2.5 Physical characteristics	12
2.6 Access time	13
2.7 Time to Ready	13
2.8 Power specifications	14
2.8.1 Power consumption	14
2.8.1.1 Typical current profiles	18
2.8.2 Conducted noise	18
2.8.3 Voltage tolerance	18
2.9 Environmental specifications	19
2.9.1 Ambient temperature	19
2.9.2 Temperature gradient	19
2.9.3 Humidity	19
2.9.3.1 Relative humidity	19
2.9.3.2 Wet bulb temperature	19
2.9.4 Altitude	19
2.9.5 Shock	19
2.9.5.1 Operating shock	19
2.9.5.2 Nonoperating shock	19
2.9.6 Vibration	20
2.9.6.1 Operating vibration	20
2.9.6.2 Nonoperating vibration	20
2.10 Electromagnetic immunity	20
2.11 Reliability	21
2.11.1 Annualized Failure Rate (AFR) and Mean Time Between Failures (MTBF)	21
2.11.2 Reliability specifications	21
2.12 Agency certification	22
2.12.1 Safety certification	22
2.12.2 Electromagnetic compatibility	22
2.12.3 FCC verification	22
2.13 Environmental protection	23
2.13.1 European Union Restriction of Hazardous Substances (RoHS) Directive	23
2.13.2 China Restriction of Hazardous Substances (RoHS) Directive	23
2.14 Corrosive environment	24
3.0 Configuring and mounting the drive	25
3.1 Handling and static-discharge precautions	25
3.2 Configuring the drive	26
3.3 Serial ATA cables and connectors	26
3.4 Drive mounting	27
3.5 Cooling	28
4.0 Serial ATA (SATA) interface	29
4.1 Hot-Plug compatibility	29
4.2 Serial ATA device plug connector pin definitions	30
4.3 Supported ATA commands	31
4.3.1 Identify Device command	33
4.3.2 Set Features command	40
4.3.3 S.M.A.R.T. commands	41
5.0 Seagate Technology support services	43
Index	45
A	45
C	45
D	45
E	45
F	45
G	45
H	45
I	45
K	45
L	46
M	46
N	46
O	46
P	46
Q	46
R	46
S	46
T	47
U	47
V	47