Seagate ST9500621SS Constellation.2 SATA Product Manual - Page 15

Start/stop times, Power specifications

Get Seagate ST9500621SS PDF manuals and user guides View all Seagate ST9500621SS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

3.7 Start/stop times Power-on to Ready (sec) Standby to Ready (sec) Ready to spindle stop (sec) 20 (max) 13 (max) 20 (max) 3.8 Power specifications The drive receives DC power (+5V or +12V) through a native SATA power connector. See Figure 5, page 25 on page 25. 3.8.1 Power consumption Power requirements for the drives are listed in the table on page 9. Typical power measurements are based on an average of drives tested, under nominal conditions, using 5.0V and 12.0V input voltage at 25°C ambient temperature. • Spinup power Spinup power is measured from the time of power-on to the time that the drive spindle reaches operating speed. • Standby mode During Standby mode, the drive accepts commands, but the drive is not spinning, and the servo and read/ write electronics are in power-down mode. The standard drive models and the SED drive models have identical hardware, however the security and encryption portion of the drive controller ASIC is enabled and functional in the SED models. This represents a small additional drain on the 5V supply of about 30mA and a commensurate increase of about 150mW in power consumption. There is no additional drain on the 12V supply. Constellation.2 Serial ATA Product Manual, Rev. F 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
Constellation.2 Serial ATA Product Manual, Rev. F
9
3.7
Start/stop times
Power-on to Ready (sec)
20 (max)
Standby to Ready (sec)
13 (max)
Ready to spindle stop (sec)
20 (max)
3.8
Power specifications
The drive receives DC power (+5V or +12V) through a native SATA power connector. See Figure 5, page 25 on
page
25.
3.8.1
Power consumption
Power requirements for the drives are listed in the table on page 9. Typical power measurements are based on
an average of drives tested, under nominal conditions, using 5.0V and 12.0V input voltage at 25°C ambient
temperature.
•
Spinup power
Spinup power is measured from the time of power-on to the time that the drive spindle reaches operating
speed.
•
Standby mode
During Standby mode, the drive accepts commands, but the drive is not spinning, and the servo and read/
write electronics are in power-down mode.
The standard drive models and the SED drive models have identical hardware, however the security and
encryption portion of the drive controller ASIC is enabled and functional in the SED models. This represents a
small additional drain on the 5V supply of about 30mA and a commensurate increase of about 150mW in
power consumption. There is no additional drain on the 12V supply.