Home » Seagate Manuals » Hard Drives » Seagate ST9900805SS » Manual Viewer

Seagate ST9900805SS Savvio 10K.1 SAS Product Manual - Page 33

Conducted noise immunity, Power sequencing, Current profiles

View all Seagate ST9900805SS manuals

Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

6.2.1 Conducted noise immunity Noise is specified as a periodic and random distribution of frequencies covering a band from DC to 10 MHz. Maximum allowed noise values given below are peak-to-peak measurements and apply at the drive power connector. 0 to 100 kHz 100 kHz to 10 MHz +5V 150mV 100mV +12V 150mV 100mV 6.2.2 Power sequencing The drive does not require power sequencing. The drive protects against inadvertent writing during power-up and down. 6.2.3 Current profiles The +12V and +5V current profiles for the ST973401SS and ST936701SS models are shown below in the following figures. Note: All times and currents are typical. See Tables 12 and 13 for maximum current requirements. Savvio SAS Product Manual, Rev. D 27

Section	Page
1.0 Scope	7
2.0 Applicable standards and reference documentation	9
2.1 Standards	9
2.1.1 Electromagnetic compatibility	9
2.1.1.1 Electromagnetic susceptibility	9
2.1.2 Electromagnetic compliance	10
2.2 Reference documents	11
3.0 General description	13
3.1 Standard features	14
3.2 Media description	14
3.3 Performance	14
3.4 Reliability	15
3.5 Formatted capacities	15
3.6 Programmable drive capacity	15
3.7 Factory-installed accessories	15
3.8 Factory-installed options	16
3.9 User-installed accessories	16
4.0 Performance characteristics	17
4.1 Internal drive characteristics	17
4.2 Seek performance characteristics	17
4.2.1 Access time	17
4.2.2 Format command execution time for 512-byte sectors (minutes)	18
4.2.3 General performance characteristics	18
4.3 Start/stop time	19
4.4 Prefetch/multi-segmented cache control	19
4.5 Cache operation	19
4.5.1 Caching write data	20
4.5.2 Prefetch operation	21
4.5.3 Optimizing cache performance for desktop and server applications	21
5.0 Reliability specifications	23
5.1 Error rates	23
5.1.1 Recoverable Errors	23
5.1.2 Unrecoverable Errors	23
5.1.3 Seek errors	24
5.1.4 Interface errors	24
5.2 Reliability and service	24
5.2.1 Mean time between failure	24
5.2.2 Preventive maintenance	24
5.2.3 Hot plugging the drive	25
5.2.4 S.M.A.R.T.	25
5.2.5 Thermal monitor	26
5.2.6 Drive Self Test (DST)	27
5.2.6.1 DST failure definition	27
5.2.6.2 Implementation	27
5.2.6.2.1 State of the drive prior to testing	28
5.2.6.2.2 Invoking DST	28
5.2.6.2.3 Short and extended tests	28
5.2.6.2.4 Log page entries	29
5.2.6.2.5 Abort	29
5.2.7 Product warranty	29
6.0 Physical/electrical specifications	31
6.1 AC power requirements	31
6.2 DC power requirements	31
6.2.1 Conducted noise immunity	33
6.2.2 Power sequencing	33
6.2.3 Current profiles	33
6.3 Power dissipation	36
6.4 Environmental limits	38
6.4.1 Temperature	38
6.4.2 Relative humidity	38
6.4.3 Effective altitude (sea level)	39
6.4.4 Shock and vibration	39
6.4.4.1 Shock	39
6.4.4.2 Vibration	41
6.4.5 Air cleanliness	41
6.4.6 Corrosive environment	41
6.4.7 Acoustics	42
6.4.8 Electromagnetic susceptibility	42
6.5 Mechanical specifications	43
7.0 Defect and error management	45
7.1 Drive internal defects/errors	45
7.2 Drive error recovery procedures	45
7.3 SAS system errors	46
8.0 Installation	47
8.1 Drive orientation	47
8.2 Cooling	48
8.3 Drive mounting	49
8.4 Grounding	49
9.0 Interface requirements	51
9.1 SAS features	51
9.1.1 task management functions	51
9.1.2 task management responses	51
9.2 Dual port support	52
9.3 SCSI commands supported	53
9.3.1 Inquiry data	57
9.3.2 Mode Sense data	57
9.4 Miscellaneous operating features and conditions	61
9.4.1 SAS physical interface	62
9.4.2 Physical characteristics	65
9.4.3 Connector requirements	65
9.4.4 Electrical description	65
9.4.5 Pin descriptions	65
9.4.6 SAS transmitters and receivers	66
9.4.7 Power	67
9.5 Signal characteristics	67
9.5.1 Ready LED Out	67
9.5.2 Differential signals	67
9.5.2.1 Eye masks	68
9.5.2.1.1 Eye masks overview	68
9.5.2.1.2 Receive eye mask	68
9.5.2.1.3 Jitter tolerance masks	69
9.5.2.2 Transmitter signal characteristics	71
9.5.2.3 Receiver signal characteristics	72
9.5.2.3.1 Jitter	72
9.5.2.3.2 Receiver jitter tolerance	73
9.5.2.3.3 Compliant jitter test pattern (CJTPAT)	73
9.5.2.3.4 Impedance specifications	73
9.5.2.4 Electrical TxRx connections	74
9.5.2.4.1 Transmitter characteristics	74
9.5.2.5 Receiver characteristics	77
10.0 Seagate Technology support services	79
Numerics	81
A	81
B	81
C	81
D	81
E	81
F	82
G	82
H	82
I	82
J	82
L	82
M	82
N	83
O	83
P	83
Q	83
R	83
S	83
T	84
U	84
V	84
W	84