Home » Seagate Manuals » Hard Drives » Seagate ST9900805SS » Manual Viewer

Seagate ST9900805SS Savvio 10K.1 SAS Product Manual - Page 48

Cooling

View all Seagate ST9900805SS manuals

Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

8.2 Cooling Cabinet cooling must be designed by the customer so that the ambient temperature immediately surrounding the drive will not exceed temperature conditions specified in Section 6.4.1, "Temperature." The rack, cabinet, or drawer environment for the drive must provide heat removal from the electronics and head and disc assembly (HDA). You should confirm that adequate heat removal is provided using the temperature measurement guidelines described in Section 6.4.1. Forced air flow may be required to keep temperatures at or below the temperatures specified in Section 6.4.1 in which case the drive should be oriented, or air flow directed, so that the least amount of air flow resistance is created while providing air flow to the electronics and HDA. Also, the shortest possible path between the air inlet and exit should be chosen to minimize the travel length of air heated by the drive and other heat sources within the rack, cabinet, or drawer environment. If forced air is determined to be necessary, possible air-flow patterns are shown in Figure 14. The air-flow patterns are created by one or more fans, either forcing or drawing air as shown in the illustrations. Conduction, convection, or other forced air-flow patterns are acceptable as long as the temperature measurement guidelines of Section 6.4.1 are met. Above unit Under unit Note. Air flows in the direction shown (back to front) or in reverse direction (front to back) Note. Air flows in the direction shown or in reverse direction (side to side) Figure 14. Air flow Above unit Under unit 42 Savvio SAS Product Manual, Rev. D

Section	Page
1.0 Scope	7
2.0 Applicable standards and reference documentation	9
2.1 Standards	9
2.1.1 Electromagnetic compatibility	9
2.1.1.1 Electromagnetic susceptibility	9
2.1.2 Electromagnetic compliance	10
2.2 Reference documents	11
3.0 General description	13
3.1 Standard features	14
3.2 Media description	14
3.3 Performance	14
3.4 Reliability	15
3.5 Formatted capacities	15
3.6 Programmable drive capacity	15
3.7 Factory-installed accessories	15
3.8 Factory-installed options	16
3.9 User-installed accessories	16
4.0 Performance characteristics	17
4.1 Internal drive characteristics	17
4.2 Seek performance characteristics	17
4.2.1 Access time	17
4.2.2 Format command execution time for 512-byte sectors (minutes)	18
4.2.3 General performance characteristics	18
4.3 Start/stop time	19
4.4 Prefetch/multi-segmented cache control	19
4.5 Cache operation	19
4.5.1 Caching write data	20
4.5.2 Prefetch operation	21
4.5.3 Optimizing cache performance for desktop and server applications	21
5.0 Reliability specifications	23
5.1 Error rates	23
5.1.1 Recoverable Errors	23
5.1.2 Unrecoverable Errors	23
5.1.3 Seek errors	24
5.1.4 Interface errors	24
5.2 Reliability and service	24
5.2.1 Mean time between failure	24
5.2.2 Preventive maintenance	24
5.2.3 Hot plugging the drive	25
5.2.4 S.M.A.R.T.	25
5.2.5 Thermal monitor	26
5.2.6 Drive Self Test (DST)	27
5.2.6.1 DST failure definition	27
5.2.6.2 Implementation	27
5.2.6.2.1 State of the drive prior to testing	28
5.2.6.2.2 Invoking DST	28
5.2.6.2.3 Short and extended tests	28
5.2.6.2.4 Log page entries	29
5.2.6.2.5 Abort	29
5.2.7 Product warranty	29
6.0 Physical/electrical specifications	31
6.1 AC power requirements	31
6.2 DC power requirements	31
6.2.1 Conducted noise immunity	33
6.2.2 Power sequencing	33
6.2.3 Current profiles	33
6.3 Power dissipation	36
6.4 Environmental limits	38
6.4.1 Temperature	38
6.4.2 Relative humidity	38
6.4.3 Effective altitude (sea level)	39
6.4.4 Shock and vibration	39
6.4.4.1 Shock	39
6.4.4.2 Vibration	41
6.4.5 Air cleanliness	41
6.4.6 Corrosive environment	41
6.4.7 Acoustics	42
6.4.8 Electromagnetic susceptibility	42
6.5 Mechanical specifications	43
7.0 Defect and error management	45
7.1 Drive internal defects/errors	45
7.2 Drive error recovery procedures	45
7.3 SAS system errors	46
8.0 Installation	47
8.1 Drive orientation	47
8.2 Cooling	48
8.3 Drive mounting	49
8.4 Grounding	49
9.0 Interface requirements	51
9.1 SAS features	51
9.1.1 task management functions	51
9.1.2 task management responses	51
9.2 Dual port support	52
9.3 SCSI commands supported	53
9.3.1 Inquiry data	57
9.3.2 Mode Sense data	57
9.4 Miscellaneous operating features and conditions	61
9.4.1 SAS physical interface	62
9.4.2 Physical characteristics	65
9.4.3 Connector requirements	65
9.4.4 Electrical description	65
9.4.5 Pin descriptions	65
9.4.6 SAS transmitters and receivers	66
9.4.7 Power	67
9.5 Signal characteristics	67
9.5.1 Ready LED Out	67
9.5.2 Differential signals	67
9.5.2.1 Eye masks	68
9.5.2.1.1 Eye masks overview	68
9.5.2.1.2 Receive eye mask	68
9.5.2.1.3 Jitter tolerance masks	69
9.5.2.2 Transmitter signal characteristics	71
9.5.2.3 Receiver signal characteristics	72
9.5.2.3.1 Jitter	72
9.5.2.3.2 Receiver jitter tolerance	73
9.5.2.3.3 Compliant jitter test pattern (CJTPAT)	73
9.5.2.3.4 Impedance specifications	73
9.5.2.4 Electrical TxRx connections	74
9.5.2.4.1 Transmitter characteristics	74
9.5.2.5 Receiver characteristics	77
10.0 Seagate Technology support services	79
Numerics	81
A	81
B	81
C	81
D	81
E	81
F	82
G	82
H	82
I	82
J	82
L	82
M	82
N	83
O	83
P	83
Q	83
R	83
S	83
T	84
U	84
V	84
W	84

Match case Limit results 1 per page

Savvio SAS Product Manual, Rev. D

8.2

Cooling

Cabinet cooling must be designed by the customer so that the ambient temperature immediately surrounding

the drive will not exceed temperature conditions specified in Section 6.4.1, "Temperature."

The rack, cabinet, or drawer environment for the drive must provide heat removal from the electronics and

head and disc assembly (HDA). You should confirm that adequate heat removal is provided using the temper-

ature measurement guidelines described in Section 6.4.1.

Forced air flow may be required to keep temperatures at or below the temperatures specified in Section 6.4.1

in which case the drive should be oriented, or air flow directed, so that the least amount of air flow resistance is

created while providing air flow to the electronics and HDA. Also, the shortest possible path between the air

inlet and exit should be chosen to minimize the travel length of air heated by the drive and other heat sources

within the rack, cabinet, or drawer environment.

If forced air is determined to be necessary, possible air-flow patterns are shown in Figure 14. The air-flow pat-

terns are created by one or more fans, either forcing or drawing air as shown in the illustrations. Conduction,

convection, or other forced air-flow patterns are acceptable as long as the temperature measurement guide-

lines of Section 6.4.1 are met.

Figure 14.

Air flow

Above unit

Under unit

Note.

Air flows in the direction shown (back to front)

or in reverse direction (front to back)

Above unit

Under unit

Note.

Air flows in the direction shown or

in reverse direction (side to side)