Sharp AN-PHCM20 Installation Instructions

Sharp AN-PHCM20 Manual

Get Sharp AN-PHCM20 PDF manuals and user guides View all Sharp AN-PHCM20 manuals
Add to My Manuals
Save this manual to your list of manuals

Sharp AN-PHCM20 manual content summary:

  • Sharp AN-PHCM20 | Installation Instructions - Page 1
    AN-PHCM20 INSTALLATION INSTRUCTIONS FOR MOUNTING BRACKET FOR USE ONLY WITH SHARP PROJECTOR MODEL XG-PH50X CEILING MOUNTING BRACKET AN-PHCM20 CEILING MOUNTING BRACKET COMBINED WITH OPTIONAL ADJUSTABLE EXTENSION TUBE MODEL AN-EP101B COPYRIGHT © 2005 SHARP ELECTRONICS CORPORATION
  • Sharp AN-PHCM20 | Installation Instructions - Page 2
    IS INTENDED TO ALERT THE USER TO THE PRESENCE OF IMPORTANT OPERATING AND MAINTENANCE (SERVICING) INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE. IMPORTANT! THE INSTALLER SHOULD READ THESE INSTRUCTIONS THOROUGHLY BEFORE BEGINNING THE INSTALLATION AND SHOULD MAKE SURE THAT ALL THE WORK IS
  • Sharp AN-PHCM20 | Installation Instructions - Page 3
    THE PROJECTOR IMAGE Please refer to the owners manual for your LCD Projector for detailed instructions of how to electrically invert the projected image SHEETROCK, LATH AND PLASTER, WILL NOT PROVIDE A SUFFICIENTLY SECURE SUPPORT. STEP 1. INSTALLATION OF THE METAL CEILING BRACKET After the location
  • Sharp AN-PHCM20 | Installation Instructions - Page 4
    INSTALLATION INSTRUCTIONS CEILING BRACKET AN-PHCM20 1.1 a. Select straddle beam or single beam installation. b. Use the ceiling bracket as a template to mark the location where the pilot holes should be drilled. c. Drill the pilot holes for the support screws using a 1/8" drill bit into the center
  • Sharp AN-PHCM20 | Installation Instructions - Page 5
    INSTALLATION INSTRUCTIONS CEILING BRACKET AN-PHCM20 FIGURE 3 ILLUSTRATION OF SINGLE BEAM CEILING BRACKET INSTALLATION Ceiling Beam Sheetrock or lath and plaster ceiling Washers 1/4 x 10 Lag Bolts Ceiling
  • Sharp AN-PHCM20 | Installation Instructions - Page 6
    INSTALLATION INSTRUCTIONS CEILING BRACKET AN-PHCM20 STEP 3 DETACH THE POSITIONING ASSEMBLY FROM THE PROJECTOR ATTACHMENT PLATE. FIGURE 5 POSITIONING KNUCKLE ASSEMBLY NOTE: PLEASE LOOK OVER THE EXACT MANNER
  • Sharp AN-PHCM20 | Installation Instructions - Page 7
    INSTALLATION INSTRUCTIONS CEILING BRACKET AN-PHCM20 STEP 5 ATTACH THE POSITIONING ASSEMBLY TO THE CEILING PLATE FIGURE 8 WASHER LOCKING NUT UPPER KNUCKLE IF YOU INTEND TO RUN AUDIO
  • Sharp AN-PHCM20 | Installation Instructions - Page 8
    INSTALLATION INSTRUCTIONS CEILING BRACKET AN-PHCM20 STEP 6 HANGING THE PROJECTOR FROM POSITIONING ASSEMBLY IT IS RECOMMENDED THAT TWO PERSONS SUPPORT THE PROJECTOR WHEN RAISING IT UP IN ORDER TO HANG IT IN PLACE. 6.1 Raise the projector with the mounting plate attached and slide the fitting (
  • Sharp AN-PHCM20 | Installation Instructions - Page 9
    INSTALLATION INSTRUCTIONS CEILING BRACKET AN-PHCM20 FIGURE 11 DETAIL OF POSITIONING ASSEMBLY CEILING PLATE PLASTIC ADJUSTABLE EXTENSION ACCESSORY IN CONJUNCTION WITH THE CEILING MOUNTING BRACKET, PLEASE REFER TO THE INSTALLATION INSTRUCTION MANUAL INCLUDED IN THE EXTENSION TUBE PACKAGE. PAGE 9
  • Sharp AN-PHCM20 | Installation Instructions - Page 10
    INSTALLATION INSTRUCTIONS CEILING BRACKET AN-PHCM20 DIMENSIONS AND MEASUREMENTS OF COMPONENTS FOR SHARP MOUNTING BRACKET AN-MBCM10 CEILING PLATE 4" WIDE X 18" LONG DISTANCE BETWEEN SETS OF MOUNTING
  • Sharp AN-PHCM20 | Installation Instructions - Page 11
    INSTALLATION INSTRUCTIONS CEILING BRACKET AN-PHCM20 ONE YEAR LIMITED WARRANTY SHARP Electronics Product the exterior of which has been damaged or defaced, which has been subject to misuse, abnormal service or handling, or which has been altered or modified in design or construction. In order to
  • Sharp AN-PHCM20 | Installation Instructions - Page 12
    COPYRIGHT © 2005 SHARP ELECTRONICS CORPORATION
  • Sharp AN-PHCM20 | Installation Instructions - Page 13
    AN-PHCM20 SUPPLEMENTAL INSTRUCTIONS FOR INSTALLATION OF 2" EXTENSIONS TO LOWER MOUNTING BRACKET FROM CEILING. CEILING PLATE COVER INSTALL ONE 2" EXTENSION OR TWO 2" EXTENSIONS HERE AS NEEDED. CONTINUE WITH STEP 5 OF THE INSTALLATION INSTRUCTIONS. COPYRIGHT © 2005 SHARP ELECTRONICS CORPORATION
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
AN-PHCM20
INSTALLATION INSTRUCTIONS
FOR
MOUNTING BRACKET FOR USE
ONLY WITH SHARP PROJECTOR
MODEL XG-PH50X
CEILING MOUNTING
BRACKET AN-PHCM20
CEILING MOUNTING
BRACKET COMBINED
WITH OPTIONAL
ADJUSTABLE
EXTENSION TUBE
MODEL AN-EP101B
COPYRIGHT ©
2005 SHARP ELECTRONICS CORPORATION