Sharp LC-26SB14U Service Manual - Page 14

When Replacing Eeprom Memory Ic - tv

Get Sharp LC-26SB14U - 26inch LCD TV PDF manuals and user guides View all Sharp LC-26SB14U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

WHEN REPLACING EEPROM (MEMORY) IC CONFIRMATION OF CHECK SUM, POWER ON TOTAL HOURS AND MICON VERSION Initial total of MEMORY IC, POWER ON total hours and MICON VERSION can be checked on the screen. Total hours are displayed in 16 system of notation. NOTE: If you set a factory initialization, the total hours is reset to "0". Please refer to "CONFIRMATION OF INITIAL DATA" when SUM DATA is not corresponding. 1. Turn on the POWER, and set to the TV mode. 2. Set the VOLUME to minimum. 3. Press both VOL. DOWN button on the set and Channel button (8) on the remote control for more than 2 seconds. 4. After the confirmation of each check sum, turn off the power. NOTE: The each item value might be different according to each set. Sub Micon check version Main Micon check version EEPROM check version Parameter CHECK SUM: 3ED6 LCD PWR ON: 0000 SUB: DA0E782141 DTV: CA09E83052 EEPROM: W34N02PE01 Picture: _dispSmartPic Initial setting data check sum. POWER ON total hours. = (16 x 16 x 16 x thousands digit value) + (16 x 16 x hundreds digit value) + (16 x tens digit value) + (ones digit value) FIG. 1 CONFIRMATION OF INITIAL DATA If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to ensure correct data settings while making reference to INITIAL SETTING TABLE (Attached "INITIAL DATA"). 1. Turn on the POWER, and set to the TV mode. 2. Set the VOLUME to minimum. 3. Press both VOL. DOWN button on the set and Channel button (6) on the remote control for more than 2 seconds. ADDRESS and DATA should appear as FIG 2. ADDRESS DATA INIT : 0001 0082 SUB: DA0E782141 DTV: CA09E83052 EEPROM: W34N02PE01 FIG. 2 4. ADDRESS is now selected and should "blink". Using the UP/DOWN buton on the remote, step through the ADDRESS until required ADDRESS to be changed is reached. 5. Press LEFT/RIGHT button to select DATA. When DATA is selected, it will "blink". 6. Again, step through the DATA using UP/DOWN button until required DATA value has been selected. 7. Pressing LEFT/RIGHT button will take you back to ADDRESS for further selection if necessary. 8. Repeat steps 4 to 6 until all data has been checked. 9. When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input. After the data input, set to the initializing of shipping. 10. Turn on the POWER, and set to the TV mode. 11. Press both VOL. DOWN button on the set and Channel button (1) on the remote control for more than 2 seconds. 12. After the finishing of the initializing of shipping, the unit will turn off automatically. The unit will now have the correct DATA for the new MEMORY IC. C-2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
C-2
1.
2.
3.
4.
Turn on the POWER, and set to the TV mode.
Set the VOLUME to minimum.
Press both VOL. DOWN button on the set and Channel button
(8)
on the remote control for more than 2 seconds.
After the confirmation of each check sum, turn off the power.
CONFIRMATION OF CHECK SUM, POWER ON TOTAL HOURS AND MICON VERSION
Initial total of MEMORY IC, POWER ON total hours and MICON VERSION can be checked on the screen. Total hours are
displayed in 16 system of notation.
NOTE:
WHEN REPLACING EEPROM (MEMORY) IC
If you set a factory initialization, the total hours is reset to "0".
Please refer to "CONFIRMATION OF INITIAL DATA" when SUM DATA is not corresponding.
4.
5.
6.
7.
8.
9.
10.
11.
12.
The unit will now have the correct DATA for the new MEMORY IC.
ADDRESS is now selected and should "blink". Using the UP/DOWN buton on the remote, step through the ADDRESS
until required ADDRESS to be changed is reached.
Press LEFT/RIGHT button to select DATA. When DATA is selected, it will "blink".
Again, step through the DATA using UP/DOWN button until required DATA value has been selected.
Pressing LEFT/RIGHT button will take you back to ADDRESS for further selection if necessary.
Repeat steps 4 to 6 until all data has been checked.
When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input.
After the data input, set to the initializing of shipping.
Turn on the POWER, and set to the TV mode.
Press both VOL. DOWN button on the set and Channel button
(1)
on the remote control for more than 2 seconds.
After the finishing of the initializing of shipping, the unit will turn off automatically.
1.
2.
3.
Turn on the POWER, and set to the TV mode.
Set the VOLUME to minimum.
Press both VOL. DOWN button on the set and Channel button
(6)
on the remote control for more than 2 seconds.
ADDRESS and DATA should appear as
FIG 2
.
If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be
taken to ensure correct data settings while making reference to INITIAL SETTING TABLE (Attached "INITIAL DATA").
CONFIRMATION OF INITIAL DATA
NOTE: The each item value might be different according to each set.
CHECK SUM:
3ED6
LCD PWR ON:
0000
SUB:
DA0E782141
DTV:
CA09E83052
EEPROM:
W34N02PE01
Picture:
_dispSmartPic
FIG. 1
Initial setting data check sum.
Sub Micon check version
Main Micon check version
ADDRESS
DATA
INIT :
0001
0082
SUB:
DA0E782141
DTV:
CA09E83052
EEPROM:
W34N02PE01
FIG. 2
POWER ON total hours.
= (16 x 16 x 16 x thousands digit
value)
+ (16 x 16 x hundreds digit value)
+ (16 x tens digit value)
+ (ones digit value)
EEPROM check version
Parameter