Sharp MT821 Operation Manual - Page 12

After recording, To remove, MiniDisc, Recording from a tuner or a CD, Manual recording, To interrupt

Get Sharp MT821 - MiniDisc Recorder - Metallic PDF manuals and user guides
UPC - 074000410473
View all Sharp MT821 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

After recording: Press the n /:OFF button while in the stop mode. 0 After the track number has been written on the disc, the power will shut off automatically. (For details about the TOC, see page 20.) To remove the MiniDisc: Turn off the power and move the OPEN lever in the direction indicated by the arrow. W Recording from a tuner or a CD (Manual recording) 0 Manual recordings can be started and stopped as you like. 1 Place the unit in the recording stand-by mode. (Perform steps 1 -- 4 in the "Synchro recording" section.) 2 Press the )I1 button. 0 Recording will start. 0 To record from a CD, press the )I1 button, and then start playback on the equipment connected to this unit. 0 Track numbers can be created while recording. (Page 17) To interrupt recording: Press the )II button while recording. 0 The unit will enter the recording stand- by mode. 0 To resume recording, press the HI but- ton again. The track number will be increased by one each time you interrupt a record- 0 ing. Recordings can not be made in the following situations: B Recording on a playback-only MiniDisc (commercially available music) D If a MiniDisc is protected against acci- dental erasure (page 9) about the recording level: B If the recording level is too low, the play- back sound volume may be too low to hear well. If it is too high, the playback sound may be greatly distorted. Since digitally recorded CDs have a large dynamic range (the volume can vary tremendously from very soft to extremely loud), do not set the recording level any higher than is necessary. Precautions when recording: B Do not jar or bump the main unit while recording. Otherwise, the recording may be unusable. 0 Depending on the strength and type 01 playback signal in the original recording, the new recording may not begin or pause at the correct point when in the synchro mode. If this happens, try making a manual recording. Precautions when inserting a MiniDisc: 0 To insert a MiniDisc, push on the middle of the edge of the disc while holding it parallel to the main unit. 0 If any resistance is felt, do not try to force the MiniDisc into the unit. It may additional more problems. If resistance is felt, remove the MiniDisc and try reloading it. Notes: l Whenever any button is pressed, the remote control display will light for ap proximately 7 seconds. 0 The REC button does not light. 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
After recording:
Press the
n
/:OFF button while in the stop
mode.
0
After the track number has been written
on the disc, the power will shut off auto-
matically. (For details about the TOC,
see page 20.)
To remove
the
MiniDisc:
Turn
off the power and move the OPEN
lever in the direction indicated by the arrow.
0
W
Recording from a tuner or a CD
(Manual recording)
0
Manual recordings can be started and
stopped as you like.
1
Place the unit in the recording stand-by
mode. (Perform steps 1
--
4 in the “Syn-
chro recording” section.)
2
Press the
)I1
button.
0
Recording will start.
0
To record from a CD, press the
)I1
button, and then start playback on the
equipment connected to this unit.
0
Track numbers can be created while
recording. (Page 17)
To interrupt recording:
Press the
)II
button while recording.
0
The unit will enter the recording stand-
by mode.
0
To resume recording, press the
HI
but-
ton again.
The track number will be increased by
one each time you interrupt a record-
ing.
Recordings
can not be made in the
following
situations:
B
Recording on a playback-only
MiniDisc
(commercially available music)
D
If a
MiniDisc is protected against acci-
dental erasure (page 9)
about
the recording level:
B
If the recording level is too low, the play-
back sound volume may be too low to
hear well. If it is too high, the playback
sound may be greatly distorted. Since
digitally recorded CDs have a large dy-
namic range (the volume can vary tre-
mendously from very soft to extremely
loud), do not set the recording level any
higher than is necessary.
Precautions
when recording:
B
Do not jar or bump the main unit while
recording. Otherwise, the recording
may be unusable.
0
Depending on the strength and type 01
playback signal in the original record-
ing, the new recording may not begin
or pause at the correct point when in
the synchro mode. If this happens, try
making a manual recording.
Precautions when inserting a MiniDisc:
0
To insert a
MiniDisc, push on the middle
of the edge of the disc while holding it
parallel to the main unit.
0
If any resistance is felt, do not try to
force the
MiniDisc
into the unit. It may
additional more problems. If resistance
is felt, remove the MiniDisc and try re-
loading it.
Notes:
l
Whenever any button is pressed, the
remote control display will light for ap
proximately 7 seconds.
0
The REC button does not light.
11