Sharp MX-4071 User Manual FAQ - Color Advanced & Essential Series 2 - Page 14

The Original Misfeeds Automatic Document, Feeder, The Paper Misfeeds

Get Sharp MX-4071 PDF manuals and user guides View all Sharp MX-4071 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

General Problems ? THE ORIGINAL MISFEEDS (AUTOMATIC DOCUMENT FEEDER) Check Is too much paper loaded into the document feeder tray? Is the original a long original? Is the original on thin paper? Is the feed roller dirty? (In a reversing single pass feeder (RSPF)) ! Solution ■ Make sure that the stack of paper in the tray is not higher than the indicator line. ► Placing the original and adding paper (page 5) ■ When using the automatic document feeder to scan a long original, set the scan size to [Long Size]. (Note that long originals cannot be copied using the copy function.) ■ Use the document glass to scan the original. If you need to use the automatic document feeder, use [Slow Scan Mode] in [Others] to scan the original. ■ Clean the surface of the paper feed roller. ► Maintenance (page 6) ? THE PAPER MISFEEDS Check ! Solution Is a torn piece of paper remaining in the machine? Is too much paper loaded in the tray? Are multiple sheets feeding at once? Are you using paper that is not within the specifications? Are the bypass tray guides adjusted to the width of the paper? Is the bypass tray extension guide pulled out? Is the bypass feed roller dirty? Is A5 (5-1/2" x 8-1/2") size paper loaded? ■ Follow the instructions in the touch panel to remove all paper. ■ Reload the paper. Load no more than the maximum number of sheets and do not exceed the indicator line. ► Placing the original and adding paper (page 5) ■ Fan the paper well before loading it. ■ Use SHARP-recommended paper. Using paper that is for other models or special paper that is not supported may result in misfeeds, creases, or smudges.  - "SUPPLIES" in Start Guide For paper that is prohibited or not recommended, see User's Manual. ■ Adjust the bypass tray guides to the width of the paper so that they slightly contact the sides of the paper. ► Placing the original and adding paper (page 5) ■ When loading large-size paper, pull out the extension guide. ► Placing the original and adding paper (page 5) ■ Clean the surface of the bypass feed roller. ► Maintenance (page 6) ■ When loading A5 (5-1/2" x 8-1/2") size paper, place the paper in the horizontal (A5R (5-1/2" x 8-1/2"R)) orientation. (Excluding tray 1 and the bypass tray) 14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
14
General Problems
THE ORIGINAL MISFEEDS (AUTOMATIC DOCUMENT
FEEDER)
Check
Solution
Is too much paper loaded into the
document feeder tray?
■
Make sure that the stack of paper in the tray is not higher than the indicator line.
►
Placing the original and adding paper (page 5)
Is the original a long original?
■
When using the automatic document feeder to scan a long original, set the scan
size to [Long Size].
(Note that long originals cannot be copied using the copy function.)
Is the original on thin paper?
■
Use the document glass to scan the original.
If you need to use the automatic document feeder, use [Slow Scan Mode] in
[Others] to scan the original.
Is the feed roller dirty?
(In a reversing single pass feeder
(RSPF))
■
Clean the surface of the paper feed roller.
►
Maintenance (page 6)
THE PAPER MISFEEDS
Check
Solution
Is a torn piece of paper remaining in
the machine?
■
Follow the instructions in the touch panel to remove all paper.
Is too much paper loaded in the tray?
■
Reload the paper. Load no more than the maximum number of sheets and do not
exceed the indicator line.
►
Placing the original and adding paper (page 5)
Are multiple sheets feeding at once?
■
Fan the paper well before loading it.
Are you using paper that is not within
the specifications?
■
Use SHARP-recommended paper.
Using paper that is for other models or special paper that is not supported may
result in misfeeds, creases, or smudges.
- "SUPPLIES" in Start Guide
For paper that is prohibited or not recommended, see User's Manual.
Are the bypass tray guides adjusted
to the width of the paper?
■
Adjust the bypass tray guides to the width of the paper so that they slightly
contact the sides of the paper.
►
Placing the original and adding paper (page 5)
Is the bypass tray extension guide
pulled out?
■
When loading large-size paper, pull out the extension guide.
►
Placing the original and adding paper (page 5)
Is the bypass feed roller dirty?
■
Clean the surface of the bypass feed roller.
►
Maintenance (page 6)
Is A5 (5-1/2" x 8-1/2") size paper
loaded?
■
When loading A5 (5-1/2" x 8-1/2") size paper, place the paper in the horizontal
(A5R (5-1/2" x 8-1/2"R)) orientation. (Excluding tray 1 and the bypass tray)
?
!
?
!