Sony BKM-FW31 Operating Instructions - Page 20

Preparations for Using the Networking Function, Installing this device

Get Sony BKM-FW31 PDF manuals and user guides View all Sony BKM-FW31 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

Preparations for Using the Networking Function You can connect this device to the network with the LAN cable (10BASE-T/ 100BASE-TX). This section describes the tasks that are required for using the networking function of this device. Installing this device Before installation • Before installation, make sure that the power to all the equipment is off. To turn the display completely off, press the 1 switch so that the display changes to standby mode, then disconnect the power cable from the wall outlet. • When you install this device, make sure that the flat panel display is locked and stable. Follow the steps below to install this device to the FWD-50PX1/50PX1N Flat Panel Display. 1 Remove the already installed option adaptor (for FWD-50PX1) or the panel cover (for FWD-50PX1N). VIDEO INPUT ADAPTOR FWD-50PX1: Loosen the two screws located on the top and bottom of the option adaptor. Use a slot screwdriver to turn the screws counterclockwise, and then remove the option adaptor carefully. When the option slot is located on the right side* 1 2 1 * The location of the option slot differs depending on the model of the Display Unit. Refer to the Instruction Manual of the FWD series as well. S VIDEO VIDEO AUDIO IN IN OUT IN OUT IN OUT L R REMOTE CONTROL S GB6 Preparations for Using the Networking Function

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
GB
6
FWD-50PX1:
Loosen the two screws
located on the top and bottom of the
option adaptor. Use a slot screwdriver
to turn the screws counterclockwise,
and then remove the option adaptor
carefully.
Preparations for Using the Networking Function
Preparations for
Using the
Networking
Function
You can connect this device to the network
with the LAN cable (10BASE-T/
100BASE-TX).
This section describes the tasks that are
required for using the networking function
of this device.
Installing this device
Before installation
•
Before installation, make sure that the
power to all the equipment is off. To turn
the display completely off, press the
1
switch so that the display changes to
standby mode, then disconnect the power
cable from the wall outlet.
•
When you install this device, make sure
that the flat panel display is locked and
stable.
Follow the steps below to install this device
to the FWD-50PX1/50PX1N Flat Panel
Display.
1
Remove the already installed option
adaptor (for FWD-50PX1) or the
panel cover (for FWD-50PX1N).
VIDEO
S VIDEO
IN
OUT
IN
OUT
R
L
AUDIO IN
VIDEO INPUT ADAPTOR
CONTROL S
REMOTE
IN
OUT
1
1
2
When the option slot is located
on the right side*
*
The location of the option slot differs
depending on the model of the Display
Unit. Refer to the Instruction Manual of
the FWD series as well.