Sony BKM-FW31 Operating Instructions - Page 23

Choose Obtain an IP address, in which this device is installed.

Get Sony BKM-FW31 PDF manuals and user guides View all Sony BKM-FW31 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

If the network environment is changed, you need to set up a new IP address again. Turn off the power of the display unit after re-setting the IP address, and then disconnect the power cord from the wall outlet. Re-connect the power cord to the wall outlet, and then turn on the power of the display unit. When the IP address has been set manually, change the setting in accordance with the new network configuration. 6 Set the IP address manually on this device following the steps given on page 11 (GB). 7 Disconnect the crossover LAN cable, then connect this device to a network in which fixed IP addresses are used, using a straight LAN cable. NOTE When you need to set an IP address manually When an IP address cannot be set automatically, follow the steps below to set an IP address manually. 1 Connect this device and the computer directly using a crossover LAN cable. 2 Choose "Obtain an IP address automatically" on the computer. 3 Turn on the power of the display unit in which this device is installed. 4 After about 30 seconds, confirm the IP address assigned to this device using the menu screen of the display unit. 5 Access the IP address confirmed in Step 4 using your browser. NOTE When you cannot access the network • Set the browser of the computer to access the Internet without using a proxy server. • If the IP address of the computer is not 169.254.xxx.xxx or the subnet mask is not 255.255.0.0, change the settings to those address values. Preparations for Using the Networking Function 9GB

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
9
GB
Preparations for Using the Networking Function
If the network environment is changed, you
need to set up a new IP address again.
Turn off the power of the display unit after
re-setting the IP address, and then
disconnect the power cord from the wall
outlet. Re-connect the power cord to the
wall outlet, and then turn on the power of
the display unit.
When the IP address has been set manually,
change the setting in accordance with the
new network configuration.
NOTE
When you need to set an IP address
manually
When an IP address cannot be set
automatically, follow the steps below to set
an IP address manually.
1
Connect this device and the computer
directly using a crossover LAN cable.
2
Choose “Obtain an IP address
automatically” on the computer.
3
Turn on the power of the display unit
in which this device is installed.
4
After about 30 seconds, confirm the
IP address assigned to this device
using the menu screen of the display
unit.
5
Access the IP address confirmed in
Step
4
using your browser.
NOTE
When you cannot access the network
•
Set the browser of the computer to access
the Internet without using a proxy server.
•
If the IP address of the computer is not
169.254.xxx.xxx or the subnet mask is
not 255.255.0.0, change the settings to
those address values.
6
Set the IP address manually on this
device following the steps given on
page 11 (GB).
7
Disconnect the crossover LAN cable,
then connect this device to a network
in which fixed IP addresses are used,
using a straight LAN cable.