Sony CMT-LS1 Operating Instructions - Page 10

Step 3: Presetting radio stations - stereo

Get Sony CMT-LS1 - Micro Hi Fi Component System PDF manuals and user guides View all Sony CMT-LS1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

Step 3: Presetting radio stations You can preset the following number of stations: - 20 for FM, and 10 for AM. 1 1 2 3 3 4 5 6 7 8 9 10/0 >10 + 5 NX x - 2 -+ .> mM 4,6 + - 6 1 Press ?/1 to turn on the power. 2 Press TUNER BAND repeatedly until the band you want appears in the display. Each time you press the button, the band changes as follows: FM y AM 3 Press PLAY/TUNING MODE repeatedly until "AUTO" appears. 4 Press TUNER +/-. The frequency indication changes and scanning stops when the system tunes in a station. "TUNED" and "STEREO" (for a stereo program) appear. When you want to stop scanning, press PLAY/TUNING MODE. 5 Press MEMORY. A preset number flashes. Proceed to step 6 while the preset number is flashing. If the unit is not operated for more than 16 seconds, the preset number disappears and the unit returns to the status of step 3. If this happens, start over from step 4. 6 Press TUNER +/- to select the preset number you want, then press ENTER. The station is stored. 7 Repeat steps 2 to 6 to preset other stations. To tune in the station manually 1 Press PLAY/TUNING MODE repeatedly until "MANUAL" appears in step 3. 2 Press TUNER +/- repeatedly to tune in the station and continue from step 5. To change the preset number Start over from step 2. To change the AM tuning interval (except for European model) The AM tuning interval is factory-set to 9 kHz (10 kHz in some areas). To change the AM tuning interval, tune in any AM station first. Turn off the power while holding down the TUNER + button. Then turn the power back on. When you change the interval, all the AM preset stations are erased. To reset the interval, repeat the same procedure. 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
10
Step 3:
Presetting radio
stations
You can preset the following number of stations:
–
20 for FM, and 10 for AM.
–
+
–
+
>10
10/0
8
9
7
5
6
4
2
3
1
m
M
–
+
x
.
>
N
X
1
4,6
2
6
3
5
1
Press
?/1
to turn on the power.
2
Press TUNER BAND repeatedly until
the band you want appears in the
display.
Each time you press the button, the band
changes as follows:
FM
y
AM
3
Press PLAY/TUNING MODE
repeatedly until “AUTO” appears.
4
Press TUNER +/–.
The frequency indication changes and
scanning stops when the system tunes in a
station. “TUNED” and “STEREO” (for a
stereo program) appear. When you want to
stop scanning, press PLAY/TUNING
MODE.
5
Press MEMORY.
A preset number flashes.
Proceed to step 6 while the preset number is
flashing. If the unit is not operated for more
than 16 seconds, the preset number
disappears and the unit returns to the status
of step 3. If this happens, start over from
step 4.
6
Press TUNER +/– to select the preset
number you want, then press ENTER.
The station is stored.
7
Repeat steps 2 to 6 to preset other
stations.
To tune in the station manually
1
Press PLAY/TUNING MODE repeatedly until
“MANUAL” appears in step 3.
2
Press TUNER +/– repeatedly to tune in the
station and continue from step 5.
To change the preset number
Start over from step 2.
To change the AM tuning
interval (except for European
model)
The AM tuning interval is factory-set to 9 kHz
(10 kHz in some areas). To change the AM tuning
interval, tune in any AM station first. Turn off the
power while holding down the TUNER + button.
Then turn the power back on. When you change
the interval, all the AM preset stations are erased.
To reset the interval, repeat the same procedure.