Sony HCD-BX5BT Operating Instructions - Page 15

Basic Operations, Pairing this system with a Bluetooth, device, To cancel passcode entry partway - bluetooth code

Get Sony HCD-BX5BT - Receiver, Amplifier, Bluetooth PDF manuals and user guides View all Sony HCD-BX5BT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

Basic Operations Pairing this system with a Bluetooth device Pairing is an operation where Bluetooth devices register with each other beforehand. Use the procedure below to pair the system with your Bluetooth device. Once a pairing operation is performed, it does not need to be performed again. If pairing is already completed, proceed to "Playing music of a Bluetooth device" (page 16). 1 Place the Bluetooth device to be connected to this system within 1 meter of the system. 2 Select the Bluetooth function. Press BLUETOOTH   on the unit. 3 Operate the Bluetooth device and perform the pairing operation. For details about the operations of the Bluetooth device, refer to the operation manual supplied with your Bluetooth device. When searching for this system with the Bluetooth device, a list of the devices found may appear in the Bluetooth device display depending on the type of Bluetooth device. This system appears as "CMTBX5BT." When establishing a connection with this system, select the audio profile (A2DP, AVRCP) at the Bluetooth device. If the Bluetooth device does not support the AVRCP profile, you cannot perform playback or other operations with the system (page 16). 4 Enter the passcode. Passcode entry may be required depending on the type of Bluetooth device. When "PIN" appears, enter the passcode at the system as follows: Press / and / on the remote (or +/ and on the unit)  to enter the same passcode that was entered at the Bluetooth device, and then press ENTER . Once pairing is completed and the connection is established, the system display changes as follows: "CONNECT"  Name of the Bluetooth device To cancel passcode entry partway Press  . Notes  "Passcode" may be called "Passkey," "PIN code," "PIN number" or "Password," etc. depending on the device.  This system only supports numerical passcodes up to 4 digits.  The pairing standby status of the system is cancelled after about 30 seconds. If pairing is not successful, redo the procedure from step 1.  While connected to a Bluetooth device, this system cannot be detected and a connection cannot be established from another Bluetooth device.  Continued 15GB

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
1´
GB
Basic Operations
Pairing this system with a Bluetooth
device
Pairing is an operation where Bluetooth
devices register with each other
beforehand. Use the procedure below
to pair the system with your Bluetooth
device. Once a pairing operation is
performed, it does not need to be
performed again. If pairing is already
completed, proceed to “Playing music of
a Bluetooth device” (page 16).
1
Place the Bluetooth device to be
connected to this system within
1 meter of the system.
2
Select the Bluetooth function.
Press BLUETOOTH

on
the unit.
3
Operate the Bluetooth device
and perform the pairing
operation.
For details about the operations of
the Bluetooth device, refer to the
operation manual supplied with your
Bluetooth device.
When searching for this system with
the Bluetooth device, a list of the
devices found may appear in the
Bluetooth device display depending
on the type of Bluetooth device.
°is system appears as “CMT-
BX5BT.”
When establishing a connection with
this system, select the audio profile
(A2DP, AVRCP) at the Bluetooth
device. If the Bluetooth device does
not support the AVRCP profile, you
cannot perform playback or other
operations with the system (page 16).
4
Enter the passcode.
Passcode entry may be required
depending on the type of Bluetooth
device.
When “PIN” appears, enter the
passcode at the system as follows:
Press
/
and
/
on the
remote (or
+/
and

/

on the unit)
to enter the
same passcode that was entered at
the Bluetooth device, and then press
ENTER
.
Once pairing is completed and the
connection is established, the system
display changes as follows:
“CONNECT”
Name of the
Bluetooth device
To cancel passcode entry partway
Press
.
Notes
“Passcode” may be called “Passkey,” “PIN
code,” “PIN number” or “Password,” etc.
depending on the device.
°is system only supports numerical
passcodes up to 4 digits.
°e pairing standby status of the system is
cancelled aſter about 30 seconds. If pairing is
not successful, redo the procedure from step
1.
While connected to a Bluetooth device, this
system cannot be detected and a connection
cannot be established from another
Bluetooth device.
Continued