Sony HCD-BX5BT Operating Instructions - Page 25

Others, Troubleshooting

Page 25 highlights

Others Troubleshooting 1 Make sure the power cord and speaker cords are correctly and firmly connected. 2 Find your problem in the checklist below, and take the indicated corrective action. If the issue persists, contact your nearest Sony dealer. If the STANDBY indicator flashes Immediately unplug the power cord, and check the following items.  If your system has a voltage selector, is the voltage selector set to the correct voltage?  Are you using only the supplied speakers?  Is anything blocking the ventilation holes on the top or back of the system? After the STANDBY indicator  stops flashing, reconnect the power cord, and turn on the system. If the issue persists, contact your nearest Sony dealer. General Sound comes from one channel, or the left and right volumes are unbalanced.  Place the speakers as symmetrically as possible.  Connect only the supplied speakers. Severe hum or noise.  Move the system away from sources of noise.  Connect the system to a different wall socket.  Install a noise filter (available separately) to the power cord. There is no sound.  If the BLUETOOTH indicator  is lit or flashing when a function other than the Bluetooth function is selected, no sound is heard through the speakers or PHONES jack . Press and hold BLUETOOTH OPR  for about 2 seconds until the BLUETOOTH indicator  turns off. The remote does not function.  Remove any obstacles between the remote and the remote sensor  on the unit, and position the unit away from fluorescent lights.  Point the remote at the system's sensor.  Move the remote closer to the system. CD/MP3 player The sound skips, or the disc will not play.  Wipe the disc clean, and replace it.  Move the system to a location away from vibration (for example, on top of a stable stand).  Move the speakers away from the system, or place them on separate stands. At high volume, speaker vibration may cause the sound to skip. Play does not start from the first track.  Press PLAY MODE  repeatedly until both "PGM" and "SHUF" disappear to return to normal play.  Continued 25GB Others

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36

±´
GB
Others
Others
Troubleshooting
1
Make sure the power cord and
speaker cords are correctly and firmly
connected.
2
Find your problem in the checklist
below, and take the indicated
corrective action.
If the issue persists, contact your
nearest Sony dealer.
If the STANDBY indicator flashes
Immediately unplug the power cord,
and check the following items.
If your system has a voltage
selector, is the voltage selector set to
the correct voltage?
Are you using only the supplied
speakers?
Is anything blocking the ventilation
holes on the top or back of the
system?
Aſter the STANDBY indicator
stops flashing, reconnect the power
cord, and turn on the system. If the
issue persists, contact your nearest
Sony dealer.
General
Sound comes from one channel,
or the left and right volumes are
unbalanced.
Place the speakers as symmetrically as
possible.
Connect only the supplied speakers.
Severe hum or noise.
Move the system away from sources of
noise.
Connect the system to a different wall
socket.
Install a noise filter (available
separately) to the power cord.
There is no sound.
If the BLUETOOTH indicator
is lit
or flashing when a function other than
the Bluetooth function is selected, no
sound is heard through the speakers
or PHONES jack
. Press and hold
BLUETOOTH OPR
for about
2 seconds until the BLUETOOTH
indicator
turns off.
The remote does not function.
Remove any obstacles between the
remote and the remote sensor
on
the unit, and position the unit away
from fluorescent lights.
Point the remote at the system’s sensor.
Move the remote closer to the system.
CD/MP3 player
The sound skips, or the disc will not
play.
Wipe the disc clean, and replace it.
Move the system to a location away
from vibration (for example, on top of
a stable stand).
Move the speakers away from the
system, or place them on separate
stands. At high volume, speaker
vibration may cause the sound to skip.
Play does not start from the first
track.
Press PLAY MODE
repeatedly until
both “PGM” and “SHUF” disappear to
return to normal play.
Continued