Sony ICD-SX25VTP Operating Instructions - Page 61

Error Messages of the IC Recorder, Error message, Cause/Remedy, Continued

Get Sony ICD-SX25VTP - Icd Recorder With Voice PDF manuals and user guides View all Sony ICD-SX25VTP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

Error Messages of the IC Recorder Additional Information Error message Cause/Remedy "BACK-D" •You set the alarm when the time is already past. Check it and set the appropriate date and time. "Err ACCESS" •The IC recorder failed in memory access. Remove and then insert the batteries. "ERR DATA" •The file is not supported by the "Digital Voice Editor" software, or the file itself is corrupted. "FULL" •The remaining memory of the IC recorder is too small. Erase some messages before recording (page 36). •When there are already 99 messages in the selected folder or the remaining memory of the IC recorder is short, you cannot divide a message. Erase some messages before dividing a message (page 36). "LO DC-IN" •An AC power adaptor that is not compatible with the IC recorder is connected. Make sure to use the AC power adaptor for the IC recorder (excluding the Korean and the People's Republic of China models). "LOW BATT" •Batteries are weak. Replace batteries with new ones. "NO DATA" •The selected folder does not have any messages. You cannot set the alarm, etc. because of this. "NO CMB" •You cannot combine messages of different modes. "PRE SET" •You set the alarm to play back a message at a date and time previously set on another message. Change the alarm setting. "REC-OP OFF"•REC-OP in the menu is se to "OFF" and you cannot add or overwrite a recording. "SET DATE" •If you do not set date and time, you cannot make alarm or time recording setting. To set date and time, see page 8. For the error messages of the "Digital Voice Editor", please refer to the online Help files. Continued 61GB

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
Additional Informatio
n
61
GB
Error message
“BACK-D”
“Err ACCESS“
“ERR DATA“
“FULL”
“LO DC-IN”
“LOW BATT“
“NO DATA“
“NO CMB”
“PRE SET”
“REC-OP OFF”
“SET DATE”
For the error messages of the “Digital Voice Editor”, please refer to the
online Help files.
Cause/Remedy
•You set the alarm when the time is already past.
Check it and set the appropriate date and time.
•The IC recorder failed in memory access.
Remove
and then insert the batteries.
•The file is not supported by the “Digital Voice
Editor” software, or the file itself is corrupted.
•The remaining memory of the IC recorder is too
small. Erase some messages before recording (page
36).
•When there are already 99 messages in the selected
folder or the remaining memory of the IC recorder is
short, you cannot divide a message. Erase some
messages before dividing a message (page 36).
•An AC power adaptor that is not compatible with the
IC recorder is connected.
Make sure to use the AC
power adaptor for the IC recorder (excluding the
Korean and the People’s Republic of China models).
•Batteries are weak. Replace batteries with new ones.
•The selected folder does not have any messages. You
cannot set the alarm, etc. because of this.
•You cannot combine messages of different modes.
•You set the alarm to play back a message at a date
and time previously set on another message. Change
the alarm setting.
•REC-OP in the menu is se to “OFF” and you cannot
add or overwrite a recording.
•If you do not set date and time, you cannot make
alarm or time recording setting. To set date and time,
see page 8.
Error Messages of the IC Recorder
Continued